Saphire Scientific 370 SS Скачать руководство пользователя страница 42

Страница: 42 / 81

SECTION 4

SAPPHIRE SCIENTIFIC MODEL 370 SS

PART#

49-038 REV F

TROUBLESHOOTING:

BLOWER / VACUUM PUMP

PROBLEM

CAUSE

SOLUTION

Loss of vacuum:

While

cleaning, the vacuum is not up

to specification. Engine RPM is

normal.

Vacuum gauge is giving an

improper reading.

Examine the tubing between the

vacuum relief valve and the vacuum

gauge and remove any blockage.

Vacuum hose(s) is damaged,

causing a suction leak.

Inspect hose(s), repair or replace.

Waste tank gaskets not sealing

properly, not positioned

properly

Inspect the gasket. Repair seal or

replace Re-position lid(s).

Plugged vacuum hose or

vacuum plumbing between

vacuum inlet and strainer

basket.

Unplug vacuum hose or inlet

plumbing.

Waste tank filter or strainer

basket is plugged.

Clean or replace filter. Clean strainer

basket.

Loose vacuum pump drive

belts.

Tighten the drive belts

Waste tank drain valve is

damaged or left open, causing a

vacuum leak.

Drain the waste tank. Close drain

valve, if open. Remove the dump valve

and, after inspecting, replace the

defective components.

Vacuum relief valve requires

adjustment or has a vacuum

leak due to damaged diaphragm.

Re-adjust the vacuum relief valve. If

the vacuum does not increase, remove

and inspect the relief valve diaphragm.

If damaged, replace

Vacuum pump is worn out.

Replace the vacuum pump.

TROUBLESHOOTING:

WATER PUMP

PROBLEM

CAUSE

SOLUTION

Loss of solution volume at

cleaning tool orifice:

Solution

pressure gauge reads normal.

Plugged orifice and/or screen in

the cleaning tool.

Unplug or replace orifice and/or screen

Internal block between the

pressure regulator manifold and

the outlet manifold, or the

solution screen is clogged

Inspect all lines, remove accumulated

debris which is blocking proper flow.

Replace any defective hoses. Remove,

inspect, and clean the solution screen.

De-scale unit and install a water

softener, if necessary.

Outlet check valve is plugged

Examine the check valve, remove any

debris

Cleaning tool valve is

malfunctioning.

Repair or replace valve.

Содержание 370 SS


















































































Результаты поиска

Содержание 370 SS

Отзывы:

Похожие инструкции для 370 SS

Бренды по названию

Популярные бренды

Saphire Scientific 370 SS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 370 SS

Отзывы:

Похожие инструкции для 370 SS

Бренды по названию

Популярные бренды