Saphire Scientific 370 SS Скачать руководство пользователя страница 21

Страница: 21 / 81

SECTION 3

SAPPHIRE SCIENTIFIC MODEL 370 SS

PART#

49-038 REV F

VACUUM SYSTEM

The engine turning an air pump (vacuum pump)

generates vacuum. The air is channeled in one

side of the vacuum pump, compressed and

discharged on the opposite side, creating

airflow. This airflow is used to do the work

necessary for the extraction process. A vacuum

nozzle applied to the carpet surface removes

moisture, dirt and spent chemicals. These

elements are conveyed back to a separating tank

utilizing hoses and the force of air. Particles of

moisture and dirt are separated in the vacuum

tank using a series of changes in direction and

velocity. The air is then filtered and rushes into

the vacuum pump.

The vacuum pump also heats incoming air as it

is compressed. The hot discharged air is forced

downstream into a silencer for noise abatement.

Exiting the silencer, this hot air is directed

through the heat exchanger

The vacuum pump speed is factory set to

maximize vacuum pressure and provide

sustained system life. Do not alter the vacuum

speed outside the recommended range shown in

the Technical Specifications section.

A level shut off sensor is located near the top of

the waste tank and will shut down the unit

before the tank is at full capacity. This protects

the vacuum pump from water damage.

Note:

Waste tank level shut off will not shut the unit

off due to high levels of foam. The use of a

quality de-foamer is recommended.

Open – No Heat

Filter Basket

Vacuum Inlet

Silencer

Vacuum Pump

Vacuum Brake

Filter

Water Box/Heat

Exchanger

Level Shut-Off Sensor

Содержание 370 SS


















































































Результаты поиска

Содержание 370 SS

Отзывы:

Похожие инструкции для 370 SS

Бренды по названию

Популярные бренды

Saphire Scientific 370 SS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 370 SS

Отзывы:

Похожие инструкции для 370 SS

Бренды по названию

Популярные бренды