manualshive.com logo in svg

Sanyo Denki SANMOTION 3E S, Инструкция по эксплуатации

Поделиться
Скачать
Sanyo Denki SANMOTION 3E S Скачать руководство пользователя страница 216

6. Servo Tuning 

 

6-15 

 

6.3.6 Adjustment method for auto-tuning 

 

Auto-tuning is a function where the servo amplifier automatically tunes to the best servo gain in 
real time. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

6.3.7 Monitoring servo gain adjustment parameters 

 

Parameters automatically adjusted when using auto-tuning can be monitored with the Digital 
Operator and the Setup software. Refer to "7. Digital operator" for use of the Digital Operator. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Procedure 1 

■

 

Select "00: AutoTun Auto-Tuning" at "Index 0x2002-1 Tuning mode [TUNMODE]" 

to estimate load inertia moment ratio by servo amplifier on a real-time basis, and 
then automatically adjust servo gain.     
Select "01:AutoTun_JRAT-Fix Automatic Tuning (JRAT Manual Setting)" to 
automatically adjust optimum servo gain based on manually set value of "Index 
0x200D-01 Load Inertia Moment Ratio 1 [JRAT1]".     

     

Procedure 2 

■

 

After setting "Tuning mode [TUNMODE]", select "Index 0x2002-1 Auto-Tuning 

Characteristic [ATCHA]" for the machine or equipment.   

 

Procedure 3 

■

 

Next, boot the servo motor and adjust "Index 0x20023 -Auto-Tuning Response 

[ATRES]" according to equipment rigidity.   

 

  Set "Auto-Tuning Response [ATRES]" at a low value initially and allow the 

machine to work about 10 times or more by commanding from upper 
controller. 

  When response is low and the positioning settling time is slow, after 

machine movement, try to improve the response and settling times by 
increasing "Auto-Tuning Response [ATRES]" gradually. 

  If increasing the response has caused the machine to get vibration, lower 

the value of the "Auto-Tuning Response [ATRES]" slightly. 

 

*  If the machine has not developed vibration, enable the Vibration 

suppression by setting the Notch filter and /or FF Vibration suppression 
frequency. Set the filter frequency to suppress mechanical vibration by 
using "6.7 Auto notch filter tuning function" and/or "6.8.2 Auto FF 
Vibration Suppression Frequency Tuning". 

*  Tuning methods are the same in "01:AutoTun_JRAT-Fix Automatic 

Tuning (JRAT Manual Setting)".     

 

 

 

Index/Sub-Idx 

Symbol 

Name 

Unit 

0x2104/0x05 

JRAT MON 

Load Inertia Moment Ratio monitor 

% 

0x2104/0x07 

MKP MON 

Model Control Gain monitor 

1/s 

0x2104/0x01 

KP MON 

Position Loop Proportional Gain monitor 

1/s 

0x2104/0x03 

KVP MON 

Velocity Loop Proportional Gain monitor 

Hz 

0x2104/0x04 

TVI MON 

Velocity Loop Integral Time Constant monitor 

ms 

0x2104/0x06 

TCFIL MON 

Torque Command Filter monitor 

Hz 

 

Содержание SANMOTION 3E S









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды