Samsung SyncMaster 460TSN Скачать руководство пользователя

Страница: 16 / 167

Slide the end of the cable with the lock at-
tached through the looped end of the Ken-
sington lock cable.

Insert the Kensington Lock into the security

slot (

) on the back of the display.

Lock the lock (

Note

•

These are general instructions. For exact in-
structions, see the User Manual supplied with
the locking device.

•

You can purchase the locking device from an
electronics store, an online shop, or our serv-
ice Center.

Connecting a Network Box (sold separately)

RGB OUT

MagicInfo

video output port

MAGICINFO OUT

It can be used by connecting it to the [HDMI IN
2 (MAGICINFO)] terminal using a DP to HDMI
cable.

LAN (LAN Connection Terminal)

Connects to a LAN cable to allow Internet or net-
work access in

MagicInfo

mode.

Connecting a Network Box (sold separately)

USB (USB Connection Terminal)

Keyboard / Mouse, Mass Storage Device Com-
patible.

AUDIO OUT

Connect a headphone or an External speaker.

RS232C (RS232C Serial PORT)

Serial port

Connecting a Network Box (sold separately)

Introduction

Содержание SyncMaster 460TSN








































































































































































Результаты поиска

Содержание SyncMaster 460TSN

Отзывы:

Похожие инструкции для SyncMaster 460TSN

Бренды по названию

Популярные бренды

Samsung SyncMaster 460TSN, Руководства пользователя

Результаты поиска

Содержание SyncMaster 460TSN

Отзывы:

Похожие инструкции для SyncMaster 460TSN

Бренды по названию

Популярные бренды