Samsung SyncMaster 460TSN Скачать руководство пользователя

Страница: 119 / 167

Reset the screen settings.

Picture [ AV / HDMI / TV / Component Mode]

Available Modes

•

PC / DVI / DisplayPort

•

Component

•

HDMI

•

MagicInfo

•

Note

•

MagicInfo

can only be enabled when a network box(sold separately) is connected.

•

A TV tuner box (sold separately) must be connected to use the TV.

Mode

The LCD Display has four automatic picture settings ("

Dynamic

", "

Standard

", "

Movie

" and "

Cus-

tom

") that are preset at the factory.

Note

Not available when

Dynamic Contrast

is set to

Dynamic

Standard

Movie

Custom

By using the on-screen menus, the contrast and brightness can be changed to your personal preference.

Note

Not available when

Dynamic Contrast

is set to

Contrast

Adjusting the LCD Display

Содержание SyncMaster 460TSN








































































































































































Результаты поиска

Содержание SyncMaster 460TSN

Отзывы:

Похожие инструкции для SyncMaster 460TSN

Бренды по названию

Популярные бренды

Samsung SyncMaster 460TSN, Руководства пользователя

Результаты поиска

Содержание SyncMaster 460TSN

Отзывы:

Похожие инструкции для SyncMaster 460TSN

Бренды по названию

Популярные бренды