Samsung SyncMaster 460TSN Скачать руководство пользователя

Страница: 64 / 167

The installation progress screen will appear.

The "InstallShield Wizard Complete" screen will appear. Click "Finish."

Note

Select " Launch MDC System" and click "Finish." The MDC Program will immediately be run.

10. If the installation is successfully completed, the quick MDC System execution icon will appear

on the desktop.

MDC execution icon may not appear depending on specification of computer system or
monitor. If that happens, press F5 Key.

Installation Problems

The installation of MDC can be affected by such factors as the video card, motherboard and the network
environment.

Uninstall

The MDC Program can be removed only by using the "Add or Remove Programs" option of the
Windows

Control Panel.

Perform the following steps remove MDC.

Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a Program".

Select MDC System from the list and then click the "Add/Delete" button.

Using Serial MDC

Using Ethernet MDC

Using the Software

Содержание SyncMaster 460TSN








































































































































































Результаты поиска

Содержание SyncMaster 460TSN

Отзывы:

Похожие инструкции для SyncMaster 460TSN

Бренды по названию

Популярные бренды

Samsung SyncMaster 460TSN, Руководства пользователя

Результаты поиска

Содержание SyncMaster 460TSN

Отзывы:

Похожие инструкции для SyncMaster 460TSN

Бренды по названию

Популярные бренды