Samsung MT3204 Series Скачать руководство пользователя

Страница: 94 / 122

Confidential

Chapter 3

Connecting Cables

MT3204 Series Installation Manual v1.0

Grounding

To comply with UL 60950, the equipment must be connected to a safety

grounding point via a permanent link. Grounding points are located on the product

for this purpose. Always connect the ground cable before fitting other cables. The

product must remain grounded continuously unless all connections to the power

supply and data network are all removed.
If equipment is grounded through a cabinet or rack, make sure it is done so

properly

Connect the ground cable first. In cabling, the connection of cables without the

connection to the ground cable may cause damage of the equipment or bodily

injury to personnel.
The purposes of the ground construction are as follows:



To prevent human life and the system from over-current, over-voltage, and

lightning.



To provide a discharge path for surge voltage generated by lightning and

power switch.



To protect the system from static electricity.



To eliminate or minimize the high-frequency potential in the system housing.



To provide a conductor for the balance and stability of high-frequency current.



To stabilize the potential of the circuit against the ground.

Connecting Ground Cable

To connect a ground cable, do the following:

Prerequisites

Before proceeding with connecting the ground cable, make sure that you have the

items mentioned in the table below:

Table 21.

Parts and Tools for Connecting Ground Cable

Содержание MT3204 Series























































































































Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды

Samsung MT3204 Series, Руководство по установке

Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды