Samsung MT3204 Series страница 12 Скачать руководство пользователя

Страница: 12 / 122

Confidential

Preface

MT3204 Series Installation Manual v1.0

xii

Rack-mountable equipment must be placed in a standard 19-inch rack and secured

with the appropriate fixings as detailed in the installation manual.

Maintenance

Maintenance must only be carried out by a suitably trained and competent

technician. All safety instructions must be carefully observed at all times.

Equipment covers should not be removed while live power and transmission is

connected unless in a controlled environment by trained technicians.

Fire

The product is powered from a -48 V DC supply. To protect against fire, the

equipment is fused.

Environment

The product must be operated in an environment with the specified relative

humidity and ambient temperature ranges.
Keep all liquids away from the equipment as accidental spillage can cause severe

damage.

Cooling

The product cools down by its own set of cooling fans housed in a fan module.

Each fan module detects a fan that is not operating normally. LEDs on the front

panel of the fan tray provide an alarm indication in the event of fan failure.
In the event of fan failure, take urgent remedial action to restore full cooling

capacity.
Take appropriate measures to ensure that fan modules do not start spinning during

repair and maintenance procedures.

Anti-Static Precautions

The circuit boards and other modules in the product are sensitive to and easily

damaged by static electricity. If any card or sub-assembly is removed from the

unit, the following anti-static precautions must be observed at all times:



Service personnel must wear anti-static wrist straps.



Circuit boards and sub-assemblies must be placed on ground conductive mats

or in conductive bags.



All tools must be discharged to ground before use.



The anti-static wrist strap and cord must be checked at regular intervals for

their suitability for use.

Содержание MT3204 Series























































































































Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды

Samsung MT3204 Series, Руководство по установке

Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды