Samsung MT3204 Series Скачать руководство пользователя

Страница: 29 / 122

Confidential

Chapter 2

Installing System

MT3204 Series Installation Manual v1.0

Transporting and Unpacking

This section describes how to transport the items to the installation place and

provides the procedure to unpack cabinets and other components.

Bringing in Items

Ensure the following at each stage of transportation of the items:



Before moving a system, check storage place for the system and remove

obstacles in advance.



When carrying the system:

Fasten the system firmly to the transport vehicle or carrier to prevent

damage to the system from a vibration or shock.

Use an elevator to prevent accidents. However, if the system must be

carried by people, ensure there are enough people to carry the system.



The system must not be shocked physically.



The system should be protected from dust, moisture, and static electricity.

Unpacking

To unpack the items, ensure the following:



The items must be packed until they reach the installation place.



The items are classified in accordance with each job specification and stored at

a place that does not interfere with working.



Unpacked systems must be installed immediately. If immediate installation of

the systems is not planned, the systems must be stored in the installation place

temporarily.



Unpack only external packing, leaving the internal packing in unpacked status.



Unpack the inner packaging after each system is placed on its installation

location.



Dispose by-products (packaging waste) in accordance with waste management

rules. Do not recycle the by-products.

Содержание MT3204 Series























































































































Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды

Samsung MT3204 Series, Руководство по установке

Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды