Samsung MT3204 Series страница 91 Скачать руководство пользователя

Страница: 91 / 122

Confidential

Chapter 3

Connecting Cables

MT3204 Series Installation Manual v1.0

Table 19.

Recommended Minimum Allowed Cable bend Radius

Type

Allowed Cable Bend Radius

Ground Cable

8 × Outer Diameter (OD)

DC Power Cable

Operation: 8 × OD

Installation: 12 × OD

Optical Cable (Outdoor)

10 × OD

UDA Cable

Operation: 5 × OD

Installation: 10 × OD

* If the allowed cable bend radius is specified by the manufacturer, comply with the bend radius specified.

Cable Binding

This process involves fixing and arranging an installed cable using binding thread,

cable ties, binding wire, and ram clamps.
Follow these guidelines when binding a cable.



Be careful not to damage the cable during binding.



Use proper cable binding tools according to the target location (indoor or

outdoor) and the type of the cable (power supply cable, optical cable, or feeder

line).



Ensure the cutting sections of the cable tie and the binding line are not exposed

to the outside. This may cause damage to the cables or personal injury.



Cut off the remainder of the cable thread by leaving about 50 mm of extra

length to prevent the knot from easily getting untied.



If there is a chance of contact-failure to occur in the connector connection due

to tension, bind the cable at the closest location to the connector.

Connector Attachment

This process involves assembling a connector to an installed cable or to a device

on the site.
Follow these guidelines when attaching the connector.



Ensure operator is fully aware of the connector assembly method before

assembling the connector. Assemble the connector in accordance with its pin

map.



Each connector has a hook to prevent its core positions from being changed.



Check the corresponding grooves before connecting the connector to another

connector.



Use a weather proof tape at the connector connection for cables that are

installed outdoor, such as feeder lines, to prevent water leakage and corrosion

from occurring at the part exposed to the outside.



Connect each cable of the connector assembly in a straight line.



Be careful when connecting the cable so that contact failure does not occur at

the connector connection due to tension.

Содержание MT3204 Series























































































































Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды

Samsung MT3204 Series, Руководство по установке

Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды