Samsung MT3204 Series Скачать руководство пользователя

Страница: 103 / 122

Confidential

Chapter 3

Connecting Cables

MT3204 Series Installation Manual v1.0

Interface Cable Connection

Remove/Insert Optical Module

If the optical module needs to be removed or inserted before connecting the cable,

follow the below process.

To remove optical module, do the following:

Hang the optical transceiver removal tool’s hook on the optical module

’

s bail

within the system.

Figure 78.

Optical Module Removal (1)

Completely remove the optical module from the optical module cage by

pulling the optical module removal Tool.

Figure 79.

Optical Module Removal (2)

When desorbing an optical module, use a dedicated tool (optical module

desorption tool) to remove the handle by opening it for about 90º.

When the optical module is detached without using the dedicated tool, the optical

module may be jammed and the handle may be damaged due to a lack of opening

capacity of the minimum necessary handle.

Optical Module

Removal Tool

Optical

Connector

Optical

Module

[System Inside]

Optical Module

Removal Tool’s Hook

Bail

[Front View]

Location to hang the

Optical Module

Removal Tool

Optical Module

Removal Tool

Optical Module

Cage

Содержание MT3204 Series























































































































Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды

Samsung MT3204 Series, Руководство по установке

Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды