Samsung DS 24D Скачать руководство пользователя страница 53

Страница: 53 / 131

OUTSIDE CALLS

MAKING AN OUTSIDE CALL

•

Lift the handset and press an idle outside line button, line group button
or dial a line access code to receive dial tone—

—press an idle out-

side line button, line group button or dial a line access code to receive
dial tone through the speaker—

—press

SPEAKER

, receive intercom

dial tone and dial a line access code.

•

Dial the telephone number.

•

Finish the call by replacing the handset or pressing the

ANS/RLS

key.

NOTE: You will receive No More Calls tone when you attempt to make a call
and there is no key available for that line.

•

If Least Cost Routing is enabled on your phone system, this button may
be labeled

LCR

or accessed by dialing an access code (usually

•

If your system is programmed to require an authorization code before
making a call, dial

plus a valid code before selecting a C.O. line.

•

If your system is programmed to require an account code before mak-
ing a call, press the

ACCT

button or dial

plus a valid bin number,

press the

ACCT

button again and then select a C.O. line.

For more information on authorization and account codes, see your system
administrator.

NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the

SPEAKER

key before dialing.

ANSWERING AN OUTSIDE CALL

•

Lift the handset and you are automatically connected to the ringing call.

See

Ring Preference under Customizing Your Keyset

—

—press the

ANS/RLS

key to automatically answer on the speakerphone.

NOTE: If a call is flashing at your keyset but not ringing, you must press the
flashing button to answer.

UNIVERSAL ANSWER

Outside lines may be programmed to ring a general alerting device. To
answer calls ringing this device, dial

or press the

key. This device can

operate in any one of the six different ring plans.

NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the

SPEAKER

key before dialing.

ADDING AN

iDCS 14 BUTTON KEY STRIP

•

Place the keyset face down on a flat surface.

•

Remove the base pedestal by placing your thumbs over the attachment
clips and press outward while simultaneously pressing down on the
keyset body with your fingertips.

•

Remove the ribbon cable knockout from the bottom of the keyset.

•

Clip the 14 button strip to the side of the keyset.

•

Plug one end of the ribbon cable into the keyset and the other end into
the 14 button strip.

•

Place the support bracket over the ribbon cable and secure with the six
screws provided.

•

Reattach the base pedestal.

REMOVE KNOCKOUTS

CONNECT RIBBON CABLE

Home Page

Table of Contents

iDCS Keyset

Содержание DS 24D




































































































































Результаты поиска

Содержание DS 24D

Отзывы:

Похожие инструкции для DS 24D

Бренды по названию

Популярные бренды

Samsung DS 24D, Инструкция пользователя

Результаты поиска

Содержание DS 24D

Отзывы:

Похожие инструкции для DS 24D

Бренды по названию

Популярные бренды