Samson 3730-6 Скачать руководство пользователя страница 99

Страница: 99 / 124

Code

no.

Parameter

– Readings,

values [default setting]

Description

Note:

Codes with marked with an asterisk (*) must be enabled with

Code 3

prior to configuration.

E4 – Unassigned –

E5* Activate PST tolerance band

monitoring

[No] · YES

Activates PST tolerance band monitoring (YES) or deactivates it

(No)

E6* PST tolerance band

0.1 to 100.0 % · ESC, [5.0]

The test is canceled when the deviation in valve position (in rela-

tion to the upper range value of the step) exceeds the adjusted

value.

E7* Max. test duration

30 to 25000 s · ESC [30]

The test is canceled when the maximum test duration is reached.

E8 – Unassigned –

E9* Reset 'Partial stroke test pa-

rameters'

Resets partial stroke test parameters

No test available

– Unassigned –

x cancelation

The test was canceled.
The valve position fell below the

x monitoring value

(

Code 49 -

p_out cancelation

The test was canceled.
The change in signal pressure (

p_out) fell below or exceeded

the reference value (

Code 49 - A9

Tolerance band exceeded

The deviation of the valve position exceeded the adjusted

PST tol-

erance band

(

Code 49 - E6

Max. test duration ex-

ceeded

The test was canceled.
The

Max. test duration

(

Code 49 - E7

) was reached.

Test canceled manually

Measured data memory full

The

Sampling time

(

Code 49 - d9

) is too low. After recording

100 data points per variable, logging is stopped, but the test

continues until it is completed.

Cancelled by internal sole-

noid valve/forced venting

The test was canceled.
The internal solenoid valve has been energized/the forced

venting has been activated.

EB 8384-6 EN

Code list

Содержание 3730-6





























































































































Результаты поиска

Содержание 3730-6

Отзывы:

Похожие инструкции для 3730-6

Бренды по названию

Популярные бренды

Samson 3730-6, Монтаж и эксплуатация

Результаты поиска

Содержание 3730-6

Отзывы:

Похожие инструкции для 3730-6

Бренды по названию

Популярные бренды