Samson 3730-6 Скачать руководство пользователя страница 12

Страница: 12 / 124

3.4

Type of application

There are two different types of application:

Control valve

and

On/off valve

. The auto-

matic mode

(AUTO) and manual mode

(MAN) can be selected in both types of

applications.

Operating

mode

Control valve

On/off valve

Automatic The positioner

follows the refer-

ence variable (w)

continuously.

Discrete analysis

of the reference

variable (w).

Reading

on dis-

play

Valve position x

in %

Valve position x

in % and

O/C

(Open/Close) in

alternating se-

quence

Manual

The positioner follows the manual

set point given over local operation.

The application type is set in Code

49 - h

(see section 7.8).

Note:

–

Depending on the application type, cer-

tain diagnostic functions cannot be per-

formed or analyzed. See Table 1.

–

Section 7.8 contains details on discrete

analysis of on/off valves.

–

In manual mode, an on/off valve can be

moved past 100 % of the nominal range

(with the closed position for ATO) or be-

low 0 % of the nominal range (with the

closed position for ATC). See section 7.1

for valve closed position.

3.5

Communication

The positioner is equipped with an interface

for HART

protocol (Highway Addressable

Remote Transducer) for communication pur-

poses. Data are transmitted in a superim-

posed frequency (FSK = Frequency Shift

Keying) on the existing signal loop for the 4

to 20 mA reference variable.
Either a HART

capable handheld commu-

nicator or a computer with FSK modem can

be used to establish communication and op-

erate the positioner.

3.5.1 Configuration using

TROVIS-VIEW 4

The positioner can be configured using the

TROVIS-VIEW 4 software for configuration

and operation. The positioner is equipped

for this purpose with an additional digital

SERIAL INTERFACE

to allow a computer to

be connected over an adapter cable from

the RS-232 or USB port of the computer to

the positioner.

The TROVIS-VIEW 4 software enables the

user to easily set parameters in the

positioner and view process parameters on-

line.

Note:

TROVIS-VIEW 4 is a free software

which can be downloaded from the

SAMSON website (

www.samson.de >

Services > Software > TROVIS-VIEW

EB 8384-6 EN

Design and principle of operation

Содержание 3730-6





























































































































Результаты поиска

Содержание 3730-6

Отзывы:

Бренды по названию

Популярные бренды

Samson 3730-6, Монтаж и эксплуатация

Результаты поиска

Содержание 3730-6

Отзывы:

Бренды по названию

Популярные бренды