SamplexPower MSK-10A Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 32

SamplexPower MSK-10A Скачать руководство пользователя страница 5

4 | SAMLEX AMERICA INC.

SAMLEX AMERICA INC. | 5

SECTION 2 |

General Information, Features

& Layout

2.1 GENERAL INFORMATION

MSK-10A is a 10A rated, Series Type of PWM (

Pulse Width Modulation

) Charge Controller. It is

based on an advanced design using a microcontroller for digital accuracy and fully automatic op-
eration. It is designed to charge 12V / 24V Lead Acid Batteries (factory preset to optimally charge
Sealed Lead Acid - AGM batteries).

2.2 FEATURES

- Advanced microcontroller based, high performance design for digital accuracy and fully

automatic and intelligent operation

- Series Type PWM (

Pulse Width Modulation

) charging for low loss, higher efficiency

charging and longer battery life

- Up to 50V Open Circuit Voltage (

Voc

) and up to 10A Short Circuit Current (

Isc

) of PV Panel(s)

- enables use of up to 150W of 12V Nominal panels for 12V battery and up to 300W, 24V
panels for 24V battery.

- Dual voltage capability – can be used with 12V / 24V batteries. 12V / 24V Nominal Battery

System is detected automatically: Battery voltage < 18V is detected as 12V battery and >18V
is detected as 24V battery

- 4 stages of charging for 100% return of capacity and for longer battery life

•

Normal

: Bulk Stage

g

Absorption Stage

g

Float Stage

•

Equalization

: On the 28

th

day of every month: Bulk Stage

g

Equalization Stage

g

Float Stage

- Factory preset for charging Sealed Lead Acid Batteries (

AGM - Absorbed Glass Mat

)

- User friendly LED display for monitoring of operation and self diagnostics for

troubleshooting

- Built-in or optional Remote Battery Temperature Sensor (

Model MSK-TS

) for battery

temperature compensation to ensure improved charging of batteries that experience wider
temperature variations during the year

- MOSFET based reverse current blocking for night-time battery discharge prevention. This

allows much lower losses as compared to Diode based blocking

-

Protections:

(i) Solar Panel over current (ii) Solar Panel short circuit (iii) Solar Panel reverse

polarity (iv) Solar Panel over voltage (v) High voltage transients on Solar Panel input (vi)
Battery reverse polarity (vii) Battery over voltage (viii) Battery over discharge (ix) Controller
/ battery overtemperature (x) Over voltage, overload and short circuit protections on Load
Terminals

2.3 APPLICATIONS

-  Recreational / Service Vehicles
-  Off grid
-  Portable Charging Kits
-  Boats and marine crafts
-  Field work / mobile offices
- Telecommunications

«
...
3
4
5
6
7
...
»

Содержание MSK-10A

































Отзывы:

Нет отзывов