manualshive.com logo in svg

SamplexPower MSK-10A, Руководство пользователя, Страница: 12 / 32

Поделиться
Скачать
SamplexPower MSK-10A Скачать руководство пользователя страница 12

12  |  SAMLEX AMERICA INC.    

 

3.4.4.2 When the battery electrolyte temperature varies from the Standard Room Temperature 
of 25º C, the values of charging / discharging voltages will be compensated based on the actual 
battery electrolyte temperature using parameter called “Battery Temperature Compensation 
Coefficient”. In this controller, this parameter is set at -3mV/ºC/Cell i.e. (i) -18mV/ºC for 6-cell, 
12V battery or (ii) -36mV/ºC for 12-cell, 24V battery.  

3.4.4.3 The controller has built-in Temperature Sensor for 

indirect and approximate

 sensing of 

battery temperature. For this, 

the controller has to be placed very close to the battery

. This built-

in sensor is the default sensor if optional Remote Battery Sensor Model MSK-TS (

Section 3.4.4.4 

below

) is 

NOT

 being used.

3.4.4.4 For more accurate sensing of the temperature of battery electrolyte, it is recommended 
that 

optional

 Remote Battery Temperature Sensor Model No. MSK-TS may be used. This 

Temperature Sensor comes with 3M/10ft cable with a cylindrical Temperature Sensor Head for 
battery end and 2-pole Female Connector for the controller end. Install this sensor as follows:

•   Attach the Cylindrical Sensor Head half way down the vertical side of the warmest part of 

the battery in the battery bank so that the sensor picks up the temperature of the electrolyte. 
Use 1 mil “PVC Pipe Wrap Tape” to tape the sensor to the battery (

pre-clean the battery 

surface with Rubbing Alcohol prior to placing the tape

) 

•  Insert the 2-pole Female Connector into the Jack marked “Temp Sensor” (

8 in Fig 2.1

) 

3.4.4.5 When the 

optional

 Remote Battery Temperature Sensor Model MSK-TS is plugged into 

the controller, the internal Temperature Sensor (

Section 3.4.4.3 above

) will be automatically 

disabled. 

3.4.5  Step 5: Install Fuse

Install 15A fuse "F1" in the battery circuit.

3.4.6  Step 6: Confirm Power ON

When battery power is applied, the controller will start operating. Refer to Table 4.1 under 
Section 4.5 for operational information through the Solar Panel / Battery / Status LEDs (

1, 2 & 3 

in Fig 2.1

).

SECTION 3  |  

Installation

Содержание MSK-10A

































Отзывы:

Нет отзывов