SamplexPower Evolution Series, Руководство пользователя, Страница: 82 / 140

82 | SAMLEX AMErICA INC.
tAbLe 6.5 ProgrAMMAbLe AnD DeFAuLt PArAMeterS - grouP "inPut high LiMit"
group Parameter name
Setting range Default value
eVo-
2212e
eVo-
3012e
eVo-
2224e
eVo-
4024e
eVo-
2212e
eVo-
3012e
eVo-
2224e
eVo-
4024e
inPut -
high LiMit
reSet VoLtAge 200.0 – 280.0V 260.0V
Cut oFF Point 1 200.0 – 280.0V 265.0V
DeteCt tiMe 1 0 – 2000 cycle 300 cycle
Cut oFF Point 2 200.0 – 280.0V 270.0V
DeteCt tiMe 2
0 – 2000 cycle 60 cycle
Cut oFF Point 3
200.0 – 280.0V 275.0V
DeteCt tiMe 3 0 – 2000 cycle 1 cycle
tAbLe 6.6 ProgrAMMAbLe AnD DeFAuLt PArAMeterS - grouP "other FunCtionS"
Parameter name
Setting range Default Value
eVo-
2212e
eVo-
3012e
eVo-
2224e
eVo-
4024e
eVo-
2212e
eVo-
3012e
eVo-
2224e
eVo-
4024e
“Power SAVing” 1 = Enable 0 = Disable 0 = Disable
–
“enter Point”
4 – 50W 6W 8W 6W 8W
–
“wAke uP Point”
5 – 50W 7W 10W 7W 10W
“reMote SwitCh”
–
for ON /Off control
through external 12V
signal fed to remote
ON / Off terminals on
the front Panel (15,
fig 2.1)
0 = button type : 12V signal is fed
through Push button Type of Switch
– Pressing of Push button > 2 sec
will switch the unit ON
–
When ON, pressing Push button
> 5 sec will turn the unit Off
1 = Switch type: 12V signal is fed
through contacts of Toggle Type of
Switch or relay contact
–
ON condition (contacts closed)
will turn the unit ON
–
Off condition (contacts open)
for 2 sec will switch the unit Off
0 = button Type
CAution! ON/Off Logic also controls the
operation of the ON/Off button on the front
panel (11, fig 2.1). The Default setting is
"button Type".
If the ON/Off Control is changed to external
"remote Switch", it will not be possible to
switch ON/Off the EVO
TM
Inverter/Charger
from the front panel ON/Off Push button
because it will work with Switch Type Logic.
It will be ON only as long as the Push buttom
is kept pressed and will switch Off when
released.
“reLAy FunCtion”
(for Status relay) 0 = Charge / other
–
Off in "Charging" Mode
–
ON in other Modes i.e. "Inverting",
"Power Saving" or "Standby"
1 = normal / Fault
–
Off in normal operating conditions
–
ON in fault Modes
2 = generator 0
–
ON when batteries drop to "LOW
VOLT ALArM" or lower for period
= "GS DETECT TIME" - Initiates
Generator start
–
Off after batteries are completely
charged till float Stage - initiates
Generator stop
2
= Generator 0
SECTIOn 6 |
Operation, Protections and Troubleshooting