Sames GNM 6080 HR Скачать руководство пользователя

Страница: 30 / 64

Index revision : C - March 2016

7105

WARNING : Before any maintenance work on the spray gun, always refer to the health and safety

instructions (

see § 2 page 8

- Disconnect the control module from the power supply.
- Check that the air and paint circuits are not pressurised.
- Dump the paint circuit.

10.2. Electropneumatic coupling

•

Step 1

: Remove paint hose. Loosen the paint

hose nut with a 15mm open-ended spanner.

•

Step 2

: Unscrew the fitting nut of the 7/10

polyurethane air hose with an open-ended
spanner of 16.

•

Step 3

: Remove the low voltage cable with a 3mm

allen key, unscrew the two captive screws from
the electropneumatic coupling.

•

Step 4

: Pull the electropneumatic coupling apart

to disconnect.

•

Step 5

: Loosen the air nipple using a 14mm open-ended spanner and replace it.

Step 1

Step 2

Step 3

Step 4

Fitting

Содержание GNM 6080 HR

































































Результаты поиска

Содержание GNM 6080 HR

Отзывы:

Похожие инструкции для GNM 6080 HR

Бренды по названию

Популярные бренды

Sames GNM 6080 HR, Руководство пользователя

Результаты поиска

Содержание GNM 6080 HR

Отзывы:

Похожие инструкции для GNM 6080 HR

Бренды по названию

Популярные бренды