manualshive.com logo in svg
background image

-  22  -

11. FINISHING A JOB

11.1. Stopping work for a short period

In the event of stopping work for a Iength of time which 

does not involve any danger of the product catalysing or 

hardening Inside the equipment or its accessories, leave 

the product suction probo (no.1, figure 1) inside the paint 

container (if a gravity tank is being used, it is not necessary 

to empty this) and perforen the depressurisation 

(Section13)

Remove the cap and dip it in cleaning solvent.

11.2. Stopping when work is finished

Once the application using the equipment is completed, it 

is necessary to empty alI the remaining product from the 

equipment and all accessories (hose, gun, suction probe or 

gravity tank, drain) before proceeding to clean these.

1.- Engáge the gun safety catch.

2.- Remove the cap and clean separately.

3.- Turn the pressure regulator (no.5, figure 1) to the 

minimum setting (anticlockwise).

4.- Place the gun in the product container and press the 

trigger to collect the product. Keep pressing the spray gun 

trigger and remove the suction probe from the product 

container, leaving it exposed to the air.

5.- Turn the pressure regulator again (no. 5, figure 1) 

clockwise. Product will start to run from the head of the 

gun, stopping after a few seconds. At that moment the 

hose and the product-containing area of the gun are empty 

of product.

Note: if the equipment is fitted with a gravity tank instead of 

an suction probe (no.1, figure 1), empty the contents of the 

tank through the gun, from the original container containing 

the product from the start.

6.- Turn the pressure regulator (no.5, figure 1) to the 

minimum setting (anticlockwise).

7.- Open the drain stopcock (no.4, figure 1) keeping a 

container at hand in which to collect the product.

8.- Disconnect the motor switch turning it to the setting 

"off”.

12. PETROL MOTOR START-UP AND SHUT-DOWN

12.1. Petrol motor start-up

 

ATTENTION:

It is necessary to read and undertand the instructions 

manual for the motor in question.

Before starting up a petrol motor, the following points 

must be checked.

1 - Check the oil level in the housing of the petrol motor.

2 - Check the oil level in the reducer – clutch housing of the 

petrol motor.

3 - Check the fuel level in the motor fuel tank.

4 - Check that the motor accelerator is at the minimum 

setting (idling).

5 - Check that the start-up switch is set to "off".

6 - Check the choke. This must be open.

7 - The fuel valve must be closed.

Once these initial checks have been made to the motor it- 

self, start-up may commence observing the following 

points:

Before starting up the motor the pumping equipment 

and accessories (hose and gun) must depressurised 

and the drain valve (no. 4 figure 1) must be open.

1 - Open the fuel valve.

2 - Set the accelerator lever to the minimum setting.

3 - Use the air choke lever in accordance with the tempera-

ture of the motor and of the environment.

4 - Move the accelerator lever slightly to the left.

5 - Turn the motor switch to the setting "on".

6 - Pull the start-up handle until a certain resistance is felt. 

At this point, pull with force.

7 - As soon as the motor is running, move the choke handle 

gradually towards the setting "open" as the motor tempera-

ture rises.

8 - Set the accelerator lever to the maximum setting (1600 

r.p.m.).

12.2. Petrol motor shut-down

Once the equipment is de pressurised (the depressurisa-

tion Section13) and completely clean, the petrol motor can 

be stopped following the steps given below:

1 - Set the accelerator to the minimum (idling) setting by 

moving the lever to the right.

2 - Turn the motor switch to the setting "off".

3 - Close the fuel valve.

 

Содержание 30941001

















































Отзывы: