background image

 

3. OPERATION 

ROYAL 

20/25 

REV.4 SEPT.2003 

Saeco International Group 

 

Cleaning

 

Empty dregs drawer

 

Storage capacity of 30 tablespoons (dreg counter reset only if warning 

to empty grounds container is triggered and machine is turned on).

 

Empty drip tray

 

With dregs drawer

 

Clean water tank.

 

As required

 

Clean coffee bean container.

 

As required

 

Clean the housing.

 

As required

 

Rinse brewing unit

 

1 x per week

 

Clean brewing unit and 

lubricate 

Clean filter

 

1 x per month

 

Descale

 

According to indicator

 

 

Descale: 

1. Place Saeco descaler into fresh water tank. 

 

 

2. Fill with about one litre of hot water. 

 

3. Remove about two to three cups via the brewing unit. 

 

4. Confirm the Descale item in the user menu by pressing twice the E-button (place a 

 

sufficiently large container under the hot water pipe). The descaler mixture is pumped at 

 

intervals through the circuit. 

 

5. Rinse: Fill the water tank once again and press the E-button twice (about 2 cups via 

 

brewing unit). 

 

 

Reset: 

Under the descale indicator item Enter - YES - Enter.

 

 

Troubleshooting

 

 

Fault/Indicator

 

Possible cause

 

Remedy

 

Does not function

 

No power

 

Check mains plug / mains 

circuit breaker / 

Ensure machine door is 

closed.

 

 

 

 

BREWING UNIT NOT 
DETECTED

 

Brewing unit not properly installed 

or not closed.

 

Install brewing unit correctly.

 

GRINDS CONTAINER NOT 
DETECTED

 

Coffee grinds container not properly 

installed.

 

Brewing unit correctly 

installed.

 

COFFEE BEAN 
CONTAINER EMPTY

 

Coffee bean container is empty.

 

Fill coffee container. 

Reset: Enter button

 

FILL WATER 
DE-AERATE

 

Water tank is empty.

 

Water tank 

 

OVERHEATING

 

After steam dispensing the system is 

not or is insufficiently de-aerated.

 

De-aerate machine.

 

GRINDER OBSTRUCTED

 

 

Clean grinder.

 

DE-AERATE

 

Air in water system.

 

Press hot water button.

 

 

 

 

Instead of coffee, only water is 
dispensed.

 

Coffee powder selection button is 

pressed, but no coffee powder is 

dispensed.

 

Add one level measure of 

coffee powder.

 

No water / steam

 

Steam nozzle blocked.

 

Free opening using a thin 

needle.

 

 

Attention: 

The coffee beans low indicator must be reset (

keep the enter button pressed for a 

minimum of 5 sec.

).

 

 

Содержание Cappuccino
















































































































































Отзывы: