RYTEC Spiral SST Скачать руководство пользователя страница 23

Страница: 23 / 36

Spiral

SST and STT Prewire Installation Manual

Spiral

SST and STT Prewire Installation Manual

■

1072124-0

■

Rev 03

■

01/22

How to connect the brake release cable to the brake release lever

Pull down

the brake release lever to the fully

released position.

The door panel should

release

under its own

weight and

drop

approximately 1/3 of the

door height.

If it does not drop,

manually pull

the door

panel down to that height.

Pull up

the brake release lever 180° to the

fully engaged position.

Try to

manually move

the door panel

up and down.
You should

NOT

be able to move the panel.

If necessary,

adjust the tension

on the cable

until both conditions are met:

▪

The door moves freely when the brake release

level is in the fully released position.

□

The door does not move when the lever is in the

fully engaged position.

Release, then reengage,

the brake

several times.

Test

after each time.

Make sure

the cable does not loosen after

multiple uses.

□

If necessary,

adjust the tension

on the cable.

□

When all tests are complete, you can

trim

the

cable (minimum trim length = 4”).

Cable stop clamp

(actual size)

SMALL PARTS

There will be some

resistance when you push

the lever down, but

it should not require

excessive force

to reach

the fully released position.

If you feel too much

resistance,

loosen the

tension on the cable.

DO NOT trim the cable

until the

brake release has been fully tested.

Make sure the clamp

is tight enough

to hold when pressure is applied.

Locate

the brake release

cable in the console.

Loosen

the retaining nut

and slide it down the length

of the brake release cable.

Thread

the cable through

the hole in the bottom of the

console

Thread

the retaining nut

up the cable and install into

the bottom of the console.

Run

the cable

down the

side column to the brake

release lever.

10mm

Pull

the cable

straight.

Allow

some slack.

Pull

down the brake release

lever

to 90°.

Run

the cable through the large hole

in the brake release tab

Loosen

the screw on the cable stop clamp

until you can

thread the cable through the clamp.

Slide

the clamp against the lever tab and

tighten

Flat

screwdriver

Cable stop clamp

(actual size)

SMALL PARTS

There will be some

resistance when you push

the lever down, but

it should not require

excessive force

to reach

the fully released position.

If you feel too much

resistance,

loosen the

tension on the cable.

DO NOT trim the cable

until the

brake release has been fully tested.

Make sure the clamp

is tight enough

to hold when pressure is applied.

Содержание Spiral SST





































Результаты поиска

Содержание Spiral SST

Отзывы:

Похожие инструкции для Spiral SST

Бренды по названию

Популярные бренды

RYTEC Spiral SST, Руководство по установке

Результаты поиска

Содержание Spiral SST

Отзывы:

Похожие инструкции для Spiral SST

Бренды по названию

Популярные бренды