manualshive.com logo in svg

Ruckus Wireless ZoneFlex 7762, Руководство по установке

Поделиться
Скачать
Ruckus Wireless ZoneFlex 7762 Скачать руководство пользователя страница 44

40

Mounting the Access Point

Step 1: Attach the Hanger Mount to the Mounting Surface

Step 1: Attach the Hanger Mount to the Mounting 
Surface

The procedure for attaching the bracket to the mounting surface depends on whether you 
are mounting the AP to a flat surface or a pole.

■

Attaching the Hanger Mount to a Flat Surface

■

Attaching the Bracket to a Pole

Attaching the Hanger Mount to a Flat Surface

WARNING:  

Ruckus Wireless strongly recommends that you wear eye protection before 

drilling holes on the mounting surface.

1.

Place the hanger mount at the exact location on the mounting surface where you want 
to mount the AP.

2.

Use the screw holes on the hanger mount as a template to mark the locations of the 
mounting holes.

3.

Remove the hanger mount from the mounting surface.

4.

Drill an 8mm-diameter hole with a depth of 36mm-38mm into each of the four markings 
that you made on the mounting surface.

5.

Insert a wall anchor (with the unthreaded part first) into each of the holes that you 
drilled.

6.

Place a metal cone on each wall anchor.

7.

Align the four screw holes on the bracket with the wall anchors that you inserted earlier.

8.

Use four flat washers and four hex nuts to attach the bracket to the mounting surface. 

9.

Using a 10mm open-end wrench, tighten the nuts to secure the bracket to the 
mounting surface. Screw torque value must be 0.4-0.5 Newton meter (Nm). As you 
tighten the nuts, the metal cones that are built into the wall anchors will expand and 
lock the wall anchors into place.

10.

Continue to 

“Step 2: Attach the Mounting Bracket to the Access Point”

.

Содержание ZoneFlex 7762

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды