button in) while audio
is
present on the
INPUT.
Turning
this
trimmer up much past the
LED
increase
the send level to the phone line due to the digital AGC!
Overdriving the input may result in distortion and very
hybrid performance!
The output level meter
is
placed
before
the output gain control.
This
is
so
that the level may be adjusted to equipment downstream
The Telos' output level meter
-LEVEL
button out,
button out) shows caller level. Adjust the trimmer marked
"OUT"
on the hybrid for a
(0
reading on your equipment while
audio
is
present on the phone line. Dial tone is
OK for
this,
but
keep in mind that dial tone level
is
about
6
dB hotter
than
voice.
Note:
When the AGC button
is
switched out, the meter reads the
telco line level and thus may
be
used to determine
if
there
is
a
phone line level problem. The meter's
indication corresponds
to a phone line level of approximately
-15
3.3
FEEDBACK CONTROL
Sometimes,
even with the exceptional trans-hybrid
loss
produced
by the digital process, trouble with feedback may occur when the
system
is
being used with an open speaker.
Generally,
this
happens only with poorer phone lines, or with very weak callers
requiring
lots of
gain
in the phone-to-speaker path.
Some
suggestions
for solution of
this
problem:
1.
the Telos
OVERRIDE
function.
When mic processing
is
being
used,
connect the hybrid input in
such a way that it gets the
unprocessed
mic signal.
The problem
here is that the mic processing combines with the internal Telos
input AGC to increase
gain
in the feedback path when no announcer
audio is present. Depending on the mic processor, the feedback
margin
could be reduced by many dB. The Telos intemal AGC
has
a
smart adaptive gate to prevent inappropriate
gain
increase, but it
is
thwarted by additional processing. If it is not possible to wire
around the processing,
try
to
set
the mic processing gate function
that the
gain
is
not "sucked-up" during pauses. You might
also
reducing the input level to the hybrid. The send level will still
be
OK, since the AGC
has
considerable range, but the system won't
ONE
ONE
OPERATION
Содержание CS9500
