RS SAILING RS Quest Скачать руководство пользователя страница 40

Страница: 40 / 86

REMEMBER

Check that both ends of the main halyard, jib halyard, and spinnaker halyard are

tied off at the bottom end of the mast so that they are within easy reach when the

mast is stepped

Note: It is recommended that the mast should always be stepped with 2 people.

If the wind is blowing, there will be a lot of pressure at the top of the mast making it

wave around. Consider finding a second helper if you feel you will struggle!

Fig. 1

Fig. 2

6.12 - Stepping the Mast

Now the mast is ready to be put up in the boat, or “stepped”.

Ensure that the forestay is fitted correctly and loose at the lower end. Ensure all 3 halyards

are tied to the pole ring on the front of the mast.

BEFORE STEPPING THE MAST, CHECK THAT YOU ARE NOT IN THE

VICINITY OF OVERHEAD POWER CABLES

Содержание RS Quest























































































Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды

RS SAILING RS Quest, Руководство по монтажу

Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды