RS SAILING RS Quest Скачать руководство пользователя страница 27

Страница: 27 / 86

If you have purchased the foredeck, it will not come attached to the boat. You will

have to add it yourself. It is much easier to do this after you have fitted out and

rigged the boat for the first time as many of the fittings are difficult to access with

the foredeck attached.

Inside one of the bucket hatches on the foredeck you will find a pack

containing all the components you need to attach the foredeck.

Remove the caps from the two holes in the

top of the mast support beam.

5.1 - Attaching the Foredeck

Lay the foredeck on it’s back (hatches down).

Add the two metal spigots in the recesses beneath the front edge of the foredeck

using the four M5x18mm bolts provided then turn the foredeck back over.

Содержание RS Quest























































































Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды

RS SAILING RS Quest, Руководство по монтажу

Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды