RS SAILING RS Quest Скачать руководство пользователя страница 14

Страница: 14 / 86

4.3 - Asymmetric spinnaker fittings.

If you have purchased the asymmetric spinnaker pack

(which is available as an option)

there are a number of fittings that must be added before you can rig the boat.

To complete this section you will need:

•Asymmetric spinnaker kit

• Pozidrive screwdriver

Remove the black plastic plugs from the holes

just to the port side of the centreboard.

Remove the next set of black plastic plugs from

the holes just forward of the centreboard.

Screw a 30mm block from the asymmetric spinnaker kit into

these holes using the two M5 x 8mm bolts provided.

a) Spinnaker Rear Halyard Block

c) Spinnaker Halyard Cleat

If you have purchased the optional foredeck, do not add it until all fittings have

been attached to the boat.

Содержание RS Quest























































































Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды

RS SAILING RS Quest, Руководство по монтажу

Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды