RS SAILING RS Quest Скачать руководство пользователя страница 66

Страница: 66 / 86

Symmetrical Spinnaker System

Spinnaker sheet

Guy

Twinning

line

Retrieval line

Pole uphaul/downhaul

g) Spinnaker pole set up

Put the spinnaker pole between the middle two knots of the yellow uphaul/downhaul and

attach the inboard end to the eye on the front of the mast.

There should be about 20mm of slack before the bottom elasticated end of the downhaul

comes up against it’s stop inside the mast. If it is significantly more than this, remove the pole

and shorten the uphaul (top end of yellow rope) accordingly. You may also need to adjust the

position of the 6 knots in the rope so that the pole is just above horizontal when between the

middle two knots.

100mm

Pole uphaul/downhaul

should go between the

pole open line and the

pole. This will keep the

pole attached to the boat

in the event of capsize.

Содержание RS Quest























































































Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды

RS SAILING RS Quest, Руководство по монтажу

Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды