RS SAILING RS Quest Скачать руководство пользователя страница 9

Страница: 9 / 86

2 - Introduction

Congratulations on the purchase of your new RS Quest, and thank you for choosing an

RS product. We are confident that you will have many hours of great sailing and racing

in this truly excellent design. The RS Quest is an exciting boat to sail and offers fantastic

sailability and performance. This manual has been compiled to help you to gain the

maximum enjoyment from your RS Quest, in a safe manner. It contains details of the

craft, the equipment supplied or fitted, its systems, and information on its safe operation

and maintenance. Please read this manual carefully and be sure that you understand its

contents before using your RS Quest.

This manual will not instruct you in boating safety or seamanship. If this is your first

boat, or if you are changing to a type of craft that you are not familiar with, for your own

safety and comfort, please ensure that you have adequate experience before assuming

command of the craft. If you are unsure, RS, your RS Dealer, or your national sailing

federation – for example, the Royal Yachting Association – will be able to advise you of a

local sailing school, or a competent instructor.

Please keep this manual in a secure place and hand it over to the new owner if

you sell the boat

For further information, spares, and accessories, please contact:

RS Sailing

Premier Way

Abbey Park

Romsey

Hampshire SO51 9DQ

Tel: +44 (0)1794 526760

Email: [email protected]

For details of your local RS Dealer, please visit www.RSsailing.com

Содержание RS Quest























































































Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды

RS SAILING RS Quest, Руководство по монтажу

Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды