RS SAILING RS Quest Скачать руководство пользователя страница 12

Страница: 12 / 86

4.1 - Toestraps

Start by attaching the toestraps to the thwart across the

middle of the cockpit.

To do this you will need a pozidrive screwdriver.

Make sure you attach the toestraps the right way round.

The ends with the webbing loop attach to the thwart. The

ends with the buckle

DO NOT

attach to the thwart.

The forward toestraps are separate and the aft toestraps

are joined together in a V shape.

Remove

ONE

of the screws from the toestrap

retainer on the thwart.

Rotate the toestrap retainer outwards to

allow you to slide the webbing loop on the

toestrap over it.

Rotate the toestrap retainer back into position

and replace the screw.

Repeat for all four toestrap retainers on the

thwart.

Webbing side up

Содержание RS Quest























































































Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды

RS SAILING RS Quest, Руководство по монтажу

Результаты поиска

Содержание RS Quest

Отзывы:

Похожие инструкции для RS Quest

Бренды по названию

Популярные бренды