Royal Enfield 350 BULLET 1949 Скачать руководство пользователя

Страница: 77 / 102

ROYAL ENFIELD WORKSHOP MANUAL

the latter once more in the hub at the end

from which it was removed. Now drive the

spindle through the hub the other way,

when it will bring out the remaining

bearing.

6. Hub Bearings

These are deep groove single row journal

ball bearings, 5/8 in. i/d by 1.9/16 in. o/d by

7/16 in. wide. The Skefko Part No. is RLS5.

Equivalent bearings of other makes are

Hoffmann LS7, Ransome and Marles LJ5/8

in., Fischer LS7.

7. Fitting Limits for Bearings

The fit of the bearings in the hub barrel is

important. The bearings are locked on the

spindle between shoulders and the distance

pieces, 30538, which in turn are held up by

the nuts on the spindle. In order to prevent

endways pre-loading of the bearings it is

essential that there is a small clearance

between the inner edge of the outer race of

the bearing and the back of the recess in

either end of the hub barrel. To prevent any

possibility of sideways movement of the

hub barrel on the bearings it is, therefore,

necessary for the bearings to be a tight fit in

the barrel but this fit must not be so tight as

to close down the outer race of the bearing

and thus overload the balls. The following

are the manufacturing tolerances which

control the fit of the bearings. The figures

for the bearings themselves are for SKF

bearings but other manufacturers' tolerances

are similar.

Bearing o/d 1.5622/1.5617 in.

Housing bore 1.5620/1.5616in.

Bearing bore .6252/.6247 in.

Shaft diameter .6252/.6248 in.

8. Refitting Ball Bearings

Note that the two ends of the spindle are

not identical. The end with the longer plain

portion between the thread and the shoulder

is fitted to the brake side of the wheel. To

refit the bearings in the hub two hollow

drifts are required, as shown in Fig. 3. One

bearing is first fitted to one end of the

spindle by means of the hollow drift; the

spindle and bearing are then entered into

one end of the hub barrel which is then

supported on one of the hollow drifts. The

other bearing is then threaded over the

upper end of the spindle and driven home by

means of the second hollow drift either

under a press, or by means of a hammer,

which will thus drive both bearings into

position simultaneously. In order to make

quite sure that there is clearance between the

inner faces of the outer bearing races and

the bottom of the recesses, fit the distance

washer, cover plate, dust excluder and the

Section K2 Page 2

www.hitchcocksmotorcycles.com

Содержание 350 BULLET 1949







































































































Результаты поиска

Содержание 350 BULLET 1949

Отзывы:

Похожие инструкции для 350 BULLET 1949

Бренды по названию

Популярные бренды

Royal Enfield 350 BULLET 1949, Руководство по техническому обслуживанию мастерской

Результаты поиска

Содержание 350 BULLET 1949

Отзывы:

Похожие инструкции для 350 BULLET 1949

Бренды по названию

Популярные бренды