Royal Enfield 350 BULLET 1949 Скачать руководство пользователя | Manualshive

Страница: 64 / 102

background image

ROYAL ENFIELD WORKSHOP MANUAL

SECTION J3

Front Fork

With Facia Panel and Aluminium Alloy Bottom Tubes

Used on " 500 Bullet," 1953 ; "Meteor 700," 1953

1. Description

The telescopic fork consists of two legs each of

which

comprises

a

main

tube

of

chrome

molybdenum  alloy  steel  tubing  which  is  securely
clamped to the Facia Panel Fork Head and to the fork
crown. Fitted over the lower end of the main tube is
the  bottom  tube  made  of  high  strength  aluminium
alloy  with  an  integral  lug  which  carries  the  wheel
spindle. Fitted on the lower end of the main tube is a
steel  bush  which  is  a  close  fit  in  the  bore  of  the
bottom  tube.  The  upper  end  of  the  bottom  tube
carries  a  bronze  bush  which  is  a  close  fit  over  the
outside  diameter  of  the  main  tube.  The  bush  is
secured  to  the  bottom  tube  by  means  of  a  threaded
housing which contains an oil seal. A

stud, known as

the "spring stud," is fitted in

the lower end of the

bottom tube and a valve port is secured to the lower
end  of  the  main  tube.  As  the  fork  operates  oil  is
forced  between  the  spring  stud  and  the  bore  of  the
valve  port  forming  a  hydraulic  damping  system.  A
compression  spring  is  fitted  inside  the  main  tube
between  the  upper  end  of  the  spring  stud  and  the
upper end of the main tube. The main tube and upper
end  of  the  bottom  tube  are  protected  by  a  one-piece
cover  secured  to  the  fork  crown  and  carrying  a
pressed steel lamp bracket welded to it.

A special version of the fork is available for

sidecar  use.  This  has  a  modified  fork  head  and  fork
crown setting the main tubes 1.1/2 in. further forward
thus  giving  less  trail  and  providing  lighter  steering
when used with a sidecar. These sidecar forks also are
fitted  with  a  steering  damper  and  have  stronger
springs.

2. Operation of Fork

The fork provides a range of movement of 6 in.

from  the  fully  extended  to  the  fully  compressed
position.  The  movement  is  controlled  by  the
compression  spring  and  by  the  hydraulic  damping
system.  The  hydraulic  damping  is  light  on  the  bump
stroke  and  heavier  on  the  rebound  stroke,  thus
damping  out  any  tendency  to  pitching  or  oscillation
without interfering unduly with the free movement of
the fork when the wheel encounters an obstacle.

Section J3 Page 1

www.hitchcocksmotorcycles.com

«
...
62
63
64
65
66
...
»

Содержание 350 BULLET 1949







































































































Отзывы:

Нет отзывов

Похожие инструкции для 350 BULLET 1949

Nils Extreme MTW03

Бренд: Abisal Страницы: 21

Бренд: Parweld Страницы: 37

Бренд: Wedze Страницы: 63

Бренд: hepco & becker Страницы: 4

WOLVERINE R MAX 2021

Бренд: Yamaha Страницы: 190

Бренд: Yamaha Страницы: 194

WOLVERINE RMAX2 2024

Бренд: Yamaha Страницы: 196

Vstar XVS650T 2004

Бренд: Yamaha Страницы: 101

Бренд: Yamaha Страницы: 104

Super Tenere ABS 2018

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 97

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 88

TDM850'99 4TX-AE3

Бренд: Yamaha Страницы: 43

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды