Royal Enfield 350 BULLET 1949 Скачать руководство пользователя

Страница: 4 / 102

ROYAL ENFIELD WORKSHOP MANUAL

SECTION A2a

Technical Data

350 Bullet 1948-1955

Cubic Capacity ...

... ...

...

346 c.c.

Stroke ...

...

90 mm.

Bore

...

... Nominal ..

70 mm.

Actual

69.874 mm./2.751 in.

(Rebore to .020 in. when wear exceeds .0065 in. and again

to .040 in. after a further .0065 in. wear.)

Compression Ratios:

Up to and including 1954

6.5 to 1

Up to and including 1955

7.25 to 1

Piston Diameter-

Bottom of Skirt-Fore and Aft 69.811/69.786 mm.

Top Lands

... 69.32/69.27 mm.

Piston Rings

Width-Plain Rings. (Two)

.0635/.0625 in.

Scraper Ring. (One)

.156/.155 in.

Radial Thickness ...................... ... . 3.085/2.833 mm.

Clearance in Grooves-Plain Rings .003/.001 in.

Scraper Ring .004/.002 in.

(Renew Piston Rings when gap exceeds 1/16 in.)

Oversize Pistons and Rings available up to +0.060 in.

Piston Boss Internal Diameter

.7501/.7499 in.

Gudgeon Pin Diameter ........... ....... .. .7501/.7499 in.

Con. Rod Small End Diameter

.7507/.7505 in.

Con. Rod Big End Diameter........... 1.62625/1.62575 in.

Crank Pin Diameter

..... ...... 1.24900/1.24875 in.

Con. Rod Floating Bush:

Outside Diameter ........ ... ........ ... . 1.6235/1.6230 in.

Inside Diameter ........... ... ........ ... . 1.2502/1.2498 in.

Width

.736/.739 in.

Driving Side Main Bearings Type

SKF.RLS8 x 2 (Early Engines)

SKF.RLS8 x 1 and SKF.CRL8 x 1 (Later Engines)

Outside Diameter 2.25 in.

Inside Diameter ........... ...... ..... 1 in.

Width

.625 in.

Timing Side Main Roller Bearing-

Outside Diameter ........ ... ........ ... ... 1.876/1.875 in.

Inside Diameter ... ....... ... ........ ... ... 1.5002/1.4998 in.

Width .................. ... ....... ... .4425/.4405 in.

Size of Rollers:

Diameter ............ ... ....... .. .2500/.2490 in.

Length ....................................... .. .328/.327 in.

Graded rollers are available in steps of .0001 from .2490

to .2500 in.

Rocker Bearing Inside Diameter ... .626/.625 in.

Rocker Spindle Diameter ............... .. .6240/.6235 in.

Inlet Valve Stem Diameter ............. ... .3430/.3425 in.

Exhaust Valve Stem Diameter .3410/.3405 in.

Valve Guide Internal Diameter .3447/.3437 in.

Valve Guide External Diameter

.6275/.6270 in.

Guide Hole in Cylinder Head .622/.623 in.

Tappet Stem Diameter

.375/.374 in.

Tappet Guide Internal Diameter ..... .3760/.3752 in.

Tappet Guide External Diameter .... .7510/.7505 in.

Guide Hole in Crankcase

.750/.749 in.

Tappet Clearance with cold engine-

Inlet .................... ... ....... ... ....... ................. Nil

Exhaust ............. ... ....... ... ....... ................. Nil

Valve Spring Free Length-

Inner .................. ... ....... ... ....... ..... 2.02 in.

Outer

.... 2.095 in.

(Renew when reduced by 3/16 in.)

Valve Timing with .012 in. clearance-

Exhaust Opens ........... ... ....... .... 75° before B.D.C

Exhaust Closes ............ ... ....... ..... 35° after T.D.C.

Inlet Opens .................. ... ....... ... 30° before T.D.C.

Inlet Closes ............................. ..... 60° after B.D.C.

Cam Spindle External Diameter ... .6240/.6235 in.

Cam Bush Internal Diameter ........ ... .6255/.6250 in.

Cam Lift ............................................ ... .3125 in.

Valve Lift (approximately) ............. ... .3125 in.

Magdyno-

Speed

.. ......... .......... .......... 1/2 Engine Speed

Points

........... ... ....... ... .012/.015 in.

Timing ........... .......... 1/2 - 7/16 in. before T.D.C.

Engine Sprocket

25 Teeth

Clutch Sprocket (all models) ......... ............. 56 Teeth

Final Drive Sprocket

............. 15 Teeth

Primary Chain-

Type ....... ........... ... ....... ... ....... ...Duplex No. 114038

................. ........... .......... .......... ............. Endless

Length ........... ....... 90 Pitches

Width

........... ... ....... ... ....... ... .628 in.

Pitch

........... ... ....... ... ....... ... .375 in.

Feed Oil Pump

Speed ........................... ... ....... ... ....... ... 1/12 Engine Speed

Piston Diameter ... ....... ... ....... .. .24975/.24950 in.

Stroke ................. ... ....... ... ....... ... ............ .5 in.

Return Oil Pump

Speed .................. ... ....... ... ....... ... 1/12 Engine Speed

Piston Diameter ... ....... ... ....... .. .37475/.37450 in.

Stroke ................. ... ....... ... ....... ... .......... .375 in.

Sparking Plug-

Type .......... Lodge H.14, KLG F.70, Champion L10S

Diameter...

14 mm.

www.hitchcocksmotorcycles.com

Содержание 350 BULLET 1949







































































































Результаты поиска

Содержание 350 BULLET 1949

Отзывы:

Похожие инструкции для 350 BULLET 1949

Бренды по названию

Популярные бренды

Royal Enfield 350 BULLET 1949, Руководство по техническому обслуживанию мастерской

Результаты поиска

Содержание 350 BULLET 1949

Отзывы:

Похожие инструкции для 350 BULLET 1949

Бренды по названию

Популярные бренды