Royal Enfield 350 BULLET 1949 Скачать руководство пользователя

Страница: 91 / 102

ROYAL ENFIELD WORKSHOP MANUAL

Section L2 Page 4

When reassembling the cush drive the

entry of the vanes between the rubbers will

be facilitated if the latter are fitted into the

driving shell first and then tilted. The

rubbers should be liberally painted with

soapsuds to faciliate entry of the vanes.

When reassembling the cush drive coat

the inside of the bore of the sprocket/brake

drum liberally with grease where it fits over

the hub barrel and also put grease on the

inner face of the lockring, 10097. The three

Simmonds nuts should be tightened down

solid as there is a shoulder on the stud

which prevents tightening of the nuts from

locking the operation of the cush drive.

11. Reassembly of Brake Shoes, Pivot Pin

and Operating Cam into Cover Plate

No difficulty should be experienced in

carrying out these operations. Make sure that

the pivot pin is really tight in the cover plate

and put a smear of grease in the grooves of

the pivot pin and on the operating face of the

cam; also on the cylindrical bearing surface

of the operating cam if this has been

removed. Fit the operating lever and

trunnion on its splines in a position to suit

the extent of wear on the linings and secure

with the nut. The range of adjustment can be

extended by moving the lever on to a

different spline.

12. Centering Cam Housing

Note that the bolt holes in the cam

housing are slotted, thus enabling the brake

shoe assembly to be centered in the drum. It

is not intended that on rear brakes the cam

housing should be left free to float but the

shoes should be centered by leaving the

screws just short of dead tight. The brake

cover plate assembly with the shoes should

then be fitted over the spindle into the brake

drum and the brake applied as hard as

possible by means of the operating lever.

This will centre the shoes in the drum. The

screws should then be tightened dead tight

and secured with the locknuts. If the shoes

are not correctly centered the brake will be

either ineffective or too fierce, depending on

whether the trailing or leading shoe first

makes contact with the drum. With the brake

assembly correctly centered and the screws

securing the cam housing correctly tightened

wear

both

linings

should

approximately equal.

13. Final Reassembly of Hub before

replacing Wheel

Before replacing the felt washers which

form the grease seals, pack both bearings

with grease.

Recommended greases are Castrolease

(Heavy), Mobilgrease (No. 4), Esso Grease,

Energrease C3 or Shell Retinax A. These

are all medium heavy lime soap or

aluminium soap greases. The use of H.M.P.

greases which have a soda soap base is not

recommended as these tend to be slightly

corrosive if any damp finds its way into the

hubs.

Make sure that the inside of the brake

drum is quite free from oil or grease, damp,

etc. Replace the felt washers, distance

collars, the brake cover plate assembly,

speedometer

drive

gearbox,

distance

collars, chain adjuster cams, the loose

section of the spindle and the spindle nut.

The wheel is then ready for reassembly into

the machine.

14. Wheel Rims

The rim fitted to both types of wheel is

WM2-19 in. pierced with 40 holes for spoke

nipples. The internal width is 1.580in. and

the diameter after building 19.062 in., the

tolerance on the circumference of the rim

shoulders where the tyre fits being

59.930/59.870 in. The standard steel

measuring tape for checking rims is 5/16 in.

wide, .011 in. thick and its length is

59.964/59.904 in.

Note that two makes of rim are used

"Dunlop" and "Palmer Jointless." These

differ in the positions of the pierced spoke

holes. The Dunlop rims have a group of

three holes on one side of the centre line,

then a single hole on the other side, a further

group of three and a single hole and so on.

Palmer rims have the holes alternately

spaced either side of the centre line. Both

rims are interchangeable and both use the

same length spokes but the method of lacing

the wheel is different (see paragraph 16).

Neither type of rim is symmetrical and care

must be taken that they are built the right

way round into the wheel.

15. Spokes

The spokes are of the single butted type

8-10 gauge with 90° countersunk heads,

angle of bend 95°100°, thread diameter

.144in., 40 threads per inch, thread form

British Standard Cycle. Spoke lengths are

as follows.

"Meteor 700," and "500 Bullet,"

Cush drive side, 7.3/4 in.

Spoke flange side 8.1/2 in.

"500 Twin" and "350 Bullet,"

Cush drive side, 7.7/8 in.

Spoke flange side 8.5/8 in.

16.

Wheel Building and Truing

The spokes are laced one over three. The

wheel must be built central in relation to the

outer faces of the distance collars which fit

www.hitchcocksmotorcycles.com

Содержание 350 BULLET 1949







































































































Результаты поиска

Содержание 350 BULLET 1949

Отзывы:

Похожие инструкции для 350 BULLET 1949

Бренды по названию

Популярные бренды

Royal Enfield 350 BULLET 1949, Руководство по техническому обслуживанию мастерской

Результаты поиска

Содержание 350 BULLET 1949

Отзывы:

Похожие инструкции для 350 BULLET 1949

Бренды по названию

Популярные бренды