Royal Enfield 350 BULLET 1949 Скачать руководство пользователя | Manualshive

Страница: 63 / 102

background image

ROYAL ENFIELD WORKSHOP MANUAL

The leads to the lighting switch and ammeter

should be disconnected from the battery, regulator,
tail lamp, etc. at their lower ends or by means of the
plug and socket connectors when these are provided.
The switch and ammeter are push fits into the rubber
bushes (LU/365408) in the fork head.

Disconnect the speedometer drive from the

speedometer  head  and  unscrew  the  steering  damper
knob and rod (if fitted) after removal of the split pin
through  the  lower  end  of  the  rod.  Undo  the  steering
damper  anchor  plate  pin  so  as  to  disconnect  the
damper from the frame of the machine.

Remove the two plug screws (38968) and loosen

the steering head clip bolt and the two fork crown
clamp bolts.

Now unscrew the fork main tubes from the fork

head and the steering stem locknut from the top of the
steering stem, turning each tube and the nut a turn or
two  at  a  time.  When  the  nut  has  been  removed  from
the  steering  stem  and  the  main  tubes  have  been
completely  unscrewed  from  the  fork  head  the
complete  fork  and  wheel  with  steering  stem  can  be
lifted out of the head lug of the frame.

8. Lubrication

The lubrication of the fork bearings is effected by

the oil which forms the hydraulic damping medium.

All  that  is  necessary  is  to  keep  sufficient  oil  in  the
fork  to  ensure  that  the  top  end  of  the  bottom  spring
stud  is  never  uncovered  even  in  the  full  rebound
position.  The  level  of  oil  in  the  fork  can  be  gauged
by removing the top plug screw and inserting a long
rod  about  3/8  in.  diameter.  If  slightly  tilted  this  will
ledge  against  the  nut  at  the  upper  end  of  the  bottom
spring  stud  and  indicate  the  level  of  oil  above  the
stud.  If  the  fork  is  empty  to  start  with,  the  quantity
required  is  approximately  7.1/2  fluid  ounces  in  each
leg.  Recommended  grades  of  oil  are  Castrolite,
Mobiloil Arctic, Essolube 20, B.P. Energol S.A.E. 20
and Shell X-100 20/20W.

9. Air Vents

The earlier forks of this type were provided with

holes  at  the  upper  end  of  each  main  tube
communicating with small vent holes in the Casquette
head.  Experience  has  shown  that  on  rough  roads  oil
may  escape  through  these  air  vents  which  in
consequence are now omitted. Escape of oil from the
earlier  forks  can  be  largely  eliminated  by  fitting
specially  long  plug  screws,  which  are  available.  The
Part Number is 40118. If these are fitted and the final
vent  hole  is  stopped  up  with  a  wooden  plug,  leakage
at  this  point  is  impossible.  Fitting  the  special  plug
screws alone is sufficient in most instances.

Section J1 Page 4

www.hitchcocksmotorcycles.com

«
...
61
62
63
64
65
...
»

Содержание 350 BULLET 1949







































































































Отзывы:

Нет отзывов

Похожие инструкции для 350 BULLET 1949

Бренд: hepco & becker Страницы: 4

Advanced Million Color Mini Motorcycle Lighting Kit

Бренд: LedGlow Страницы: 3

Бренд: FDC Страницы: 6

Бренд: Honda Страницы: 141

KTM 1190 LED Light Bar

Бренд: CYCLOPS Страницы: 4

Бренд: LAZER Страницы: 11

Бренд: Yamaha Страницы: 166

Бренд: Yamaha Страницы: 166

Бренд: Yamaha Страницы: 198

Бренд: Yamaha Страницы: 274

Бренд: Yamaha Страницы: 356

Бренд: Yamaha Страницы: 376

Бренд: Yamaha Страницы: 564

Бренд: Yamaha Страницы: 392

Бренд: Yamaha Страницы: 402

Бренд: Yamaha Страницы: 674

Бренд: Yamaha Страницы: 586

Бренд: Yamaha Страницы: 568

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды