Royal Enfield 350 BULLET 1949 Скачать руководство пользователя | Manualshive

Страница: 83 / 102

background image

ROYAL ENFIELD WORKSHOP MANUAL

Section L1 Page 2

in the same position.* Disconnect the
speedometer driving cable and slide the wheel
out of the fork ends, tilting it so as to disengage
the end of the brake shoe pivot pin from the slot
in the fork end.

When replacing the wheel make sure that the

dogs on the gear in the speedometer drive
gearbox are engaged with the slots in the end of
the hub barrel. Make sure also that the
speedometer

drive

gearbox

is

correctly

positioned so that there is no sudden bend in the
driving cable. When replacing the

* Note that the wheel is not necessarily

correctly lined up when the same notch position

is used on both adjuster cams. Once the position

of the cams which gives correct alignment has

been found this alignment will, however, be

maintained if both cams are moved the same

number of notches.

3. Removal and Replacement of Complete
Wheel for Access to Brake

Place the machine on the centre stand and

remove  the  dual  seat  (if  fitted)  and  detachable
portion of the rear mudguard as if for removal of
the  main  portion  of  the  wheel  only.  Disconnect
the  rear  driving  chain  at  the  spring  link  and
remove  the  chain  from  the  rear  wheel  sprocket
leaving it in position on the gearbox countershaft
sprocket.  Unscrew  the  rear  brake  rod  adjusting
nut completely and depress the brake pedal so as
to  disengage  the  rod  from  the  trunnion  in  the
brake  operating  lever.  Unscrew  the  brake  cover
plate anchor nut, 7598, and remove this together
with  the  washer  behind  it.  Unscrew  the  loose
section of the spindle, 39336, two or three turns
and the spindle nut, 36651, by a similar amount.
Mark the chain adjuster cams to ensure replacing

www.hitchcocksmotorcycles.com

«
...
81
82
83
84
85
...
»

Содержание 350 BULLET 1949







































































































Отзывы:

Нет отзывов

Похожие инструкции для 350 BULLET 1949

Бренд: Kabuto Страницы: 12

690 Enduro R 2013

Бренд: KTM Страницы: 234

2005-2006 Hammer

Бренд: Victory Motorcycles Страницы: 12

Бренд: APRILIA Страницы: 9

HIGHSIDER VICTORY

Бренд: Paaschburg & Wunderlich Страницы: 5

Бренд: Malossi Страницы: 36

H-X-ADV-07-01-AL

Бренд: SRC Страницы: 6

Бренд: Honda Страницы: 143

DRAG STAR XVS125

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 82

CRUX REV YD110-1 2016

Бренд: Yamaha Страницы: 82

Diversion XJ600N

Бренд: Yamaha Страницы: 101

Drag Star XVS1100

Бренд: Yamaha Страницы: 104

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды