Rowe 7770 Скачать руководство пользователя

Страница: 63 / 110

5 - 2

Part No. 900-68702

7800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog

SHELF REMOVAL

Shelf removal in the Rowe Snack/Candy
Vendor is an easy operation. Remove the
shelf as follows:

Carefully pull the shelf out to a normal
service position (

See Figure 5-2

Lift the front of the shelf and continue
to pull forward, making sure that the
retaining studs clear the gap in the shelf
supports (

See Figure 5-3

). Continue

pulling the shelf forward until it stops.

Lower the front end of the shelf so that
it will hang vertically in front of the
machine. Lower shelves will not hang
vertically.

Grasp the sides of the shelf and lift up
and out.

Drive Motor

The 7800 Deluxe Snack/Candy Vendor
uses a high RPM DC motor. The DC
motor has a high starting torque and should
provide long, reliable life.

GUM AND MINT UNIT
REMOVAL

Pull out and remove the shelf above
the gum and mint assembly.

DO NOT try to turn the motors by
hand. Damage to the motor will
result. Allow the machine to home
the motors.

Remove the left shroud.

Remove the left and right (white) nylon
shelf guides.

Pull the gum and mint release levers
forward and slide the shelf out to the
stop position.

Disconnect the spring overtravel
prevention bracket.

Shift the shelf to left and pull it out.

To reassemble, reverse this procedure.

Fig. 5-1

Normal Service Position

Fig. 5-2

Shelf Removal Primary Position

Содержание 7770















































































































Результаты поиска

Содержание 7770

Отзывы:

Похожие инструкции для 7770

Бренды по названию

Популярные бренды

Rowe 7770, Руководство по обслуживанию на поле и каталог запасных частей

Результаты поиска

Содержание 7770

Отзывы:

Похожие инструкции для 7770

Бренды по названию

Популярные бренды