Rowe 7770 Скачать руководство пользователя страница 110

Страница: 110 / 110

Section 6: TROUBLESHOOTING & SELF-DIAGNOSTICS

6-3

25553601

LOW COIN SENSOR ELECTRICAL CHECK

Perform the following procedure to ensure that the Low Coin Sensor is functioning properly.

1. Turn the Bill Changer power to OFF.

2. Remove the hopper and empty it of all coins.

WARNING:
Make sure that the power is OFF before performing the following step.

3. Locate connector P3 on the Changer Control Computer (CCC). Connect a DC

voltmeter to P3-5 (GND) and P3-4 (+).

4. Replace the empty hopper and turn Bill Changer power to ON. The voltmeter

should read less than +.5 volts DC.

5. Tape 2 x 2 inch piece of aluminum foil around the end of a non-metallic object

such as a long plastic ruler or wood stick. Figure 6-3, the Hopper Cleaning Brush
is good for this purpose.

6. Place the foil end of the test object

inside

the hopper as close as possible to the

location of the sensor

(Figure 6-2, Hopper Sensor Area)

. The voltmeter should

now have a reading of no less than 4.3 volts and a maximum of 5.5 volts.

Figure 6-2

Hopper Sensor

Area

Sensor Area

Figure 6-3

Hopper Cleaning

Brush

Foil

Содержание 7770















































































































Результаты поиска

Содержание 7770

Отзывы:

Бренды по названию

Популярные бренды

Rowe 7770, Руководство по обслуживанию на поле и каталог запасных частей

Результаты поиска

Содержание 7770

Отзывы:

Бренды по названию

Популярные бренды