Rowe 7770 Скачать руководство пользователя

Страница: 41 / 110

3 - 14

Part No. 900-68701

800 Deluxe Snack / Candy Vendors Field Service Manaul & Parts Catalog

FUNCT?”.

Press <6> on the keypad.

The display will read “MTR DE-
TECT”.

Press <0> to run the detection.

The display will read “DETECTING”
and return to the ‘-’ prompt. View the
Motor Count option to verify all
installed motors were detected.

G. Hopper Configuration

Press <0> on the keypad.

The display will read “MTR
FUNCT?”.

Press <7> on the keypad.

The display will read “HOPPER Y” or
“HOPPER N”.

Press <1> to toggle Y/N. If the
Executive Credit System is configured,
this feature is not available and the
display will not change to “HOPPER
Y”.

Press <5> to save and advance to the
next menu option.

The display will read “HC VAL x.xx”
where x.xx represents the value of the
coins loaded in the bulk hopper.

Press <1> to change the coin value to
0.25, 1.00, or 2.00.

Press <5> to save and advance to the
next menu option.

10. The display will read “H PR CNT”.
11. Press <1> to change "HPR COUNT"

to "HPR LEVEL" and back to "HPR
COUNT".

12. Press <5> to save and advance to the

next menu option.

13. The display will read "C CNTxxx"

meaning Coin Count where xxx
represents the number of the coins
loaded in the bulk hopper.

14. Press <1> to add 50 to the hopper

count.

15. Press <2> to subtract 50 from the

hopper count.

16. Press <5> to save and advance to the

next menu option.

17. The display will read “A OVR x.xx”

meaning Automatic Over where x.xx
represents the amount of credit that
must be established on the snack
machine before the machine will
automatically dispense change from
the bulk hopper.

18. Press <1> to add to the value.
19. Press <2> to subtract from the value.

20. Press <5> to save and advance to the

next menu option.

21. The display will read “CHNG ALL

Y” or “CHNG ALL N”.

22. Press <1> to toggle Y/N.

23. Press <5> to save and advance to the

next menu option.

24. The display will read “HOPPER

TST”.

25. Press <0> to turn on the hopper

motor for 5 seconds.

26. The display will return to the ‘-’

prompt.

Содержание 7770















































































































Результаты поиска

Содержание 7770

Отзывы:

Похожие инструкции для 7770

Бренды по названию

Популярные бренды

Rowe 7770, Руководство по обслуживанию на поле и каталог запасных частей

Результаты поиска

Содержание 7770

Отзывы:

Похожие инструкции для 7770

Бренды по названию

Популярные бренды