Rowe 7770 Скачать руководство пользователя страница 108

Страница: 108 / 110

Section 6: TROUBLESHOOTING & SELF-DIAGNOSTICS

6-1

25553601

MISCELLANEOUS PROBLEMS

The following problems may occur in the Bill Changer without causing a fault code.

ERRATIC PAYOUT

Problem:

The changer is not consistently dispensing the correct number of coins.

Symptom:

One vend is short a coin. The next vend contains an extra coin.

Corrective Action:

Check the coin chute on the back of the dispenser.

Most likely, a coin is

getting hung up in the dispenser coin chute, after it has been “counted” by the
detector, then being shaken loose by a later vend. Check the coin chute for any dirt
or obstruction that might cause a coin to hang up.

LARGE NUMBER OF VALID BILLS REJECTED

Problem:

The bill acceptor rejects a large number of valid bills.

Corrective Action:

Refer to the Troubleshooting Chart in the

Bill Acceptor Field Service Manual and Parts

Catalog

included with your Bill Changer.

BILLS JAM FREQUENTLY

Problem:

Bills repeatedly become jammed in the Bill Acceptor transport.

Corrective Action:

Refer to the Bill Jamming Checklist in the

Bill Acceptor Field Service Manual and Parts

Catalog

included with your Bill Changer.

Содержание 7770















































































































Результаты поиска

Содержание 7770

Отзывы:

Бренды по названию

Популярные бренды

Rowe 7770, Руководство по обслуживанию на поле и каталог запасных частей

Результаты поиска

Содержание 7770

Отзывы:

Бренды по названию

Популярные бренды