Roving Networks RN-171 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 71

Roving Networks RN-171 Скачать руководство пользователя страница 7

WiFly GSX

www.rovingnetworks.com

WiFlyRN171-um 2/23/2011

809 University Avenue

•

Los Gatos, CA 95032

•

Tel (408) 395-6539

•[email protected]

~

7

~

Factory default is hardware flow control disabled; CTS and RTS are not required.

PIO’s are not 5.0 VDC tolerant. If using a 5.0 VDC circuit, input, PIO and UART input pins require a
resistor divider. A suggestion is to use a 10Kresistor in series with 20k resistor to ground.

2.4.

Status Indictors

PIO 4, 5 and 6 are active high and can be connected to external LEDs to provide network, connection and
data status.

3.

Configuration

3.1.

Entering Command Mode

Upon power up, the device will be in data mode. To enter command mode, exactly the three characters

$$$

must be sent. The device will respond with

CMD

.

While in command mode, the device will accept ASCII bytes as commands.
To exit command mode, send

exit<cr>.

The device will respond with “EXIT”.

Parameters, such as the SSID, channel, IP address, Serial Port settings, and all other settings can be viewed
and configured in command mode.

ASCII characters can be sent through a terminal emulator connected to the UART or via Telnet.  When
using the UART communications settings should match the settings used when RN-131g connects, for
example: the default is 9600 baudrate, 8 bits, No Parity, 1 stop bit, and hardware flow control disabled.

Use TeraTerm as your terminal emulator. Please

DO NOT

use HyperTerminal as it is known to have issues

with our products.TeraTerm can be downloaded from our
website:

http://www.rovingnetworks.com/support/teraterm.zip

.

Type

$$$

on in the terminal emulator. You should see “

CMD

”returned to you. This will verify that your

cable and comm. settings are correct. Most valid commands will return an “

AOK

”, response, and invalid

ones will return an

“ERR”

description.

To exit command mode, type

“exit“<cr>.

Condition

PIO6=Red LED

PIO5=Yellow LED

PIO4=Green LED

ON solid

Connected over TCP

Fast blink

Not Associated

Rx/Tx data transfer

No IP address

Slow blink

IP address OK

OFF Associated

«
...
5
6
7
8
9
...
»

Содержание RN-171








































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды