manualshive.com logo in svg

Roving Networks RN-171, Руководство пользователя и справочник команд

Поделиться
Скачать
Roving Networks RN-171 Скачать руководство пользователя страница 67

WiFly GSX

 

www.rovingnetworks.com

 

 

 

 

 

WiFlyRN171-um      2/23/2011

 

809 University Avenue 

•

 Los Gatos, CA 95032  

•

Tel (408) 395-6539 

•[email protected]

 

~

 

67

 

~

 

•

 

We no longer pass serial data received into the UART back over telnet when in remote command 
mode 
 

Features 

 

User specified default configuration

 - You can now specified a USER configuration as the factory reset 

settings.  The function of PIO9 has been changed slightly.  See section 17.1 

 

Configurable Device ID

 – There is now an additional user programmable device ID that can be used 

for storing serial numbers, product name, device type or other information.  The device ID is part of the 
broadcast “hello” UDP message that the module sends out to identify itself. Use the command show 
deviceid to display the current setting. For more information on using this command see the “set 
optional” section command  
 

UDP broadcast packet – 

By defaultthe WiFly module now sends out a UDP broadcast to 

255.255.255.255 on port 55555 at a programmable interval.  The broadcast address, port and interval are 
set using the set broadcast commands.  See section 11 

 

Known Issues 

 

WiFly Module has trouble associating with some 802.11.n access points.  The module will crash and 
reboot repeatedly.  We have seen this behavior with Linksys and Dlink router/access points.   If you 
disable the .n capability on the router the module will associated correctly.  
 
Flow control is not functional.    
 

Current Firmware Version 2.09 7/10/2009 

 

•

 

Sleep mode was drawing 70uA instead of the expected 4uA due to an oscillator that was not 
disabled before going to sleep. Refer to the RN-131G datasheet for the proper low-power hardware 
configuration. 
 

•

 

Fixed closing of TCP port on TCP RESET.  Previously the module was not handling remote TCP 
reset correctly and would disconnect which resulted in a printout of ERR= -5, TCP port was not 
closed properly. 

 

•

 

Fixed clearing and setting of strings in several set commands.  In these cases the strings could be 
erased, but not reset. 

o

 

set comm remote 

o

 

set comm open 

o

 

set comm close 

o

 

set dns name 

o

 

set dns backup 

 

Содержание RN-171








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды