manualshive.com logo in svg

Roving Networks RN-171, Руководство пользователя и справочник команд

Поделиться
Скачать
Roving Networks RN-171 Скачать руководство пользователя страница 2

WiFly GSX

 

www.rovingnetworks.com

 

 

 

 

 

WiFlyRN171-um      2/23/2011

 

809 University Avenue 

•

 Los Gatos, CA 95032  

•

Tel (408) 395-6539 

•[email protected]

 

~

 

2

 

~

 

 

1. Overview

............................................................................................................................................................ 4

 

2. Hardware 

Interface

............................................................................................................................................ 6

 

2.1. Power ................................................................................................................................................6 
2.2. Reset..................................................................................................................................................6 
2.3. UART................................................................................................................................................6 
2.4. Status 

Indictors..................................................................................................................................7 

3. Configuration

..................................................................................................................................................... 7

 

3.1. Entering 

Command 

Mode.................................................................................................................7 

4. WiFly 

Command 

Reference

........................................................................................................................... 10

 

4.1. Command 

Syntax............................................................................................................................10 

4.2. Command 

Organization ..................................................................................................................10 

5. SET 

Commands

............................................................................................................................................... 11

 

5.1. Adhoc 

Parameters ...........................................................................................................................11 

5.2. Broadcast 

Parameters......................................................................................................................11 

5.3. COMM 

Parameters .........................................................................................................................12 

5.4. DNS 

Parameters..............................................................................................................................13 

5.5. FTP 

Parameters...............................................................................................................................13 

5.6. IP 

Parameters ..................................................................................................................................14 

5.7. Optional 

Parameters........................................................................................................................16 

5.8. SystemParameters ...........................................................................................................................16 
5.9. 

Time Server Parameters..................................................................................................................17 

5.10. UART 

Parameters...........................................................................................................................18 

5.11. WLAN 

Parameters..........................................................................................................................19 

5.12. Sensor 

Parameters...........................................................................................................................22 

6. Get 

Commands

................................................................................................................................................ 23

 

7. Status 

Commands

............................................................................................................................................ 24

 

8. Action 

Commands

........................................................................................................................................... 25

 

9. File 

IO 

Commands

.......................................................................................................................................... 26

 

10. 

Advanced features and Settings

................................................................................................................. 27

 

10.1.  System Timers and Auto Connect Timers ......................................................................................28 
10.2.  Wake on Sensor Input.....................................................................................................................31 
10.3. Wake 

on 

UART ..............................................................................................................................31 

10.5.  Setting GPIO direction, Alternate Functions and Disabling LEDs ................................................33 
10.6.  Setting Debug Print levels ..............................................................................................................36 
10.7.  Using the Real Time Clock Function..............................................................................................36 
10.8. Time 

Stamping 

Packets...................................................................................................................37 

11. 

Sending data using UDP .................................................................................................................38 

11.1. Overview.........................................................................................................................................38 
11.2. UDP 

Auto 

Pairing ...........................................................................................................................39 

11.3. UDP 

Retry.......................................................................................................................................39 

11.4.  Using the UDP Broadcast function.................................................................................................39 

12. 

Joining Networks and Making Connections

............................................................................................ 41

 

Содержание RN-171








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды