manualshive.com logo in svg

Roving Networks RN-171, Руководство пользователя и справочник команд

Поделиться
Скачать
Roving Networks RN-171 Скачать руководство пользователя страница 6

WiFly GSX

 

www.rovingnetworks.com

 

 

 

 

 

WiFlyRN171-um      2/23/2011

 

809 University Avenue 

•

 Los Gatos, CA 95032  

•

Tel (408) 395-6539 

•[email protected]

 

~

 

6

 

~

 

2.

 

Hardware Interface 

 
See the specific module data sheets on the Roving Networks website for hardware specifications, and layout 
information.  
 

2.1.

 

Power 

 
There are two options for powering the RN-131G module directly. 
 
DC SUPPLY:  

Apply 3.3 VDC power to VBATT (pin 20), and V3.3IN (pin 21).  
Tie 3.3VREG-IN (pin 18) to GROUND.    
Leave 3.3V-REG-OUT (Pin 17) floating/no connect. 

 
BATTERY:     

Apply battery = 2.0 to 3.3VDC to VBATT (pin 20).   

LeaveV3.3IN pin 21 floating/no connect. 
Tie pin 17 to pin 18. (This enables the on board battery boost 3.3V switcher).  

 
There is a built-in brownout monitor which will shut down the chip when the voltage drops below 2.0 VDC. 
 

WARNING

:  Do NOT exceed the voltage ratings damage to the module will result.

 

 

#1: The Sensor inputs SENS0-7 are extremely sensitive to over voltage.  Under no conditions should 
these pins be driven above 1.2VDC.  Placing any voltage above this will permanently damage the 
radio module and render it useless. 
 
#2: Placing 5VDC or any voltage above 3.3Vdc into the VDD pins of the module will permanently 
damage the radio module.   
 
#3: Placing 3.3Vdc into the PIO’s while they are set as outputs will permanently damage the module.  
The failure mode is a short across GND and VCC.   

 

2.2.

 

Reset 

 
Reset is active LOW and is optional/does not need to be connected.   The reset pin is 3.3V tolerant and has 
an internal pull up of 100K to the VBATT.  
 

2.3.

 

UART 

 
Connect a common ground when using the external TX, RX inputs.  
 
For a 3 wire DB-9 interface (connect TX, RX, GND only)  
 

Содержание RN-171








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды