manualshive.com logo in svg

Roving Networks RN-171, Руководство пользователя и справочник команд

Поделиться
Скачать
Roving Networks RN-171 Скачать руководство пользователя страница 37

WiFly GSX

 

www.rovingnetworks.com

 

 

 

 

 

WiFlyRN171-um      2/23/2011

 

809 University Avenue 

•

 Los Gatos, CA 95032  

•

Tel (408) 395-6539 

•[email protected]

 

~

 

37

 

~

 

UpTime=8 s 
 
<2.20>

time 

 
<2.20>

show t

 

Time=08:51:31 
UpTime=15 s 
 
NOTE: the WiFly module must by successfully associated with a network for the module to contact the 
sNTP server. 
 
Alternatively, the module can be configured to get the time whenever it powers up by setting the time 
enable to 1.  Any value greater than 1 gets time continuously every <value> minutes.  

 

 
To configure the Wifly module to get time upon power up 

<2.20>

set time enable 1

 

AOK 
<2.20>

get time

 

ENA=1 
ADDR=129.6.15.28:123 
ZONE=7 

 
To view a complete listing of the time variable use the command 

<2.20>

show t t

 

Time=09:02:10 
UpTime=653 s 
Powerup=1792 s 
RTC=7753271426558 ms 
timera=66885 

 

10.8.

 

Time Stamping Packets 

 
This feature can be used to automatically append 8 bytes to a TCP or UDP packet. 
 

setip flags  0x87    

(enables timestamp and keeps other default settings )   

 
TIME STAMP  (MSB to LSB ) 

User’s TCP or UDP packet Data 

63-56 

55-48 

47-40 

39-32 

31-24 

23-16 

15-8

7-0 

 
The 8 bytes represents the 64 bit raw value of the Real Time Clock register.   The data is appended 
before calculating TCP checksum so it will pass thru the TCP stack correctly.  This register counts at 32,768 
Hz.  If the timeserver function is enabled, the RTC should accurately reflect the real time.   This register is 
also counting while in sleep mode. 
 

Содержание RN-171








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды