manualshive.com logo in svg

Roving Networks RN-171, Руководство пользователя и справочник команд

Поделиться
Скачать
Roving Networks RN-171 Скачать руководство пользователя страница 13

WiFly GSX

 

www.rovingnetworks.com

 

 

 

 

 

WiFlyRN171-um      2/23/2011

 

809 University Avenue 

•

 Los Gatos, CA 95032  

•

Tel (408) 395-6539 

•[email protected]

 

~

 

13

 

~

 

setcomm size  <value>

 

sets the flush size.  An IP packet will be sent each time “value” bytes are 
received. Default is 64 bytes.  You should set this value to the largest 
possible setting to maximize TCP/IP performance. Maximum value = 
1420 (at 9600) bytes. 

 
NOTE:  This value is set automatically when the baudrate is set, in an 
attempt to optimize the link.  It is assumed that higher baudrates equates 
to more data and hence the flush size is increased. 

 

Flush size is one of three ways to control TCP/IP packet forwarding.  The 
others are match character and timer.  For more information see section 
10.4 on UART Receiver.

 

 

setcomm time <num>

 

sets the flush timer. An IP packet will be sent if no additional bytes are 
received for “num” milliseconds. Num is one milliseconds interval. 1 is 
the minimum value. Default is 10 (10 milliseconds). Setting this value to 0 
will disable forwarding based on the flush timer. 

 

Flush timer is one of three ways to control TCP/IP packet forwarding.  
The others are match character and size.  For more information see section 
10.1 on System Timers and Auto Connect Timers

 

 

5.4.

 

DNS Parameters 

 

setdns address <addr>

 

sets the IP address of the DNS sever.  This is auto-set when using DHCP, 
and needs to be set in STATIC IP or Auto-IP modes. 

 

setdns name  <string>

 

sets the name of the host for TCP/IP connections. 

 

setdns backup  <string>

 

sets the name of the backup host for TCP/IP connections. 

 

5.5.

 

FTP Parameters 

 

set ftp filename  <file>

 

sets the name of the file transferred when issuing the “ftp u”  or “ftp g” 
commands.   

 

set ftp addr<addr>

 

sets the ftp server IP address. 

 

set ftp remote  <port>

 

sets the ftp server remote port number (default is 21). 

 

set ftp user <name>

 

sets the ftp user name for accessing the FTP server.  

 

set ftp pass <pass>

 

sets the ftp password for accessing the FTP server.  

 
 

Содержание RN-171








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды