manualshive.com logo in svg

Roving Networks RN-171, Руководство пользователя и справочник команд

Поделиться
Скачать
Roving Networks RN-171 Скачать руководство пользователя страница 4

WiFly GSX

 

www.rovingnetworks.com

 

 

 

 

 

WiFlyRN171-um      2/23/2011

 

809 University Avenue 

•

 Los Gatos, CA 95032  

•

Tel (408) 395-6539 

•[email protected]

 

~

 

4

 

~

 

 
 

 
 

 
 

1.

 

Overview 

 
The “WiFly” radio module is a complete stand alone embedded wireless LAN access device.   The device 
has on board TCP/IP stack and applications.  Requiring only 4 pins (POWER, TX, RX, GND) to design in.    
Once initial configuration is set, the radio can automatically access the WiFi network and send/receive 
serial data over UART. 
 

•

 

Fully Qualified and Wi-Fi Certified 2.4GHz IEEE 802.11b/g transceiver 

•

 

High throughput, up to 4Mbps sustained data rate with TCP/IP and WPA2 

•

 

Ultra-low power (4uA sleep, 40mA Rx, 210mA max Tx) 

•

 

Small, compact surface mount module 

•

 

On board ceramic chip antenna and U.FL connector for external antenna 

•

 

8 Mbit flash memory and 128 KB RAM 

•

 

UART and SPI (future) data/control interfaces 

•

 

10 general purpose digital I/O 

•

 

8 analog inputs 

•

 

Real-time clock for wakeup and time stamping/data logging 

•

 

Accepts 3.3V regulated or 2-3V battery with on board boost regulators 

•

 

Supports Adhoc and Infrastructure mode connections 

•

 

On board ECOS-OS, TCP/IP stacks 

•

 

Wi-Fi Alliance certified for WPA2-PSK 

•

 

FCC / CE/ ICS certified and RoHS compliant 

 

Features

 

•

 

Host Data Rate up to 1 Mbps for UART,  4Mbps SPI 

•

 

Memory 128 KB RAM, 2MB ROM, 2 KB battery-backed memory, 8 Mbit Flash. 

•

 

Intelligent, built-in power management with programmable wakeup 

•

 

Can be powered from regulated 3.3VDC source or 2.0-3.0V batteries 

•

 

Real time clock for time stamping, auto-sleep and auto-wakeup modes 

•

 

Configuration over UART or wireless interfaces using simple ASCII commands 

•

 

Over the air firmware upgrade (FTP), and data file upload. 

•

 

Secure WiFi authentication WEP-128, WPA-PSK (TKIP), WPA2-PSK (AES). 

Содержание RN-171








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды