manualshive.com logo in svg

Roving Networks RN-171, Руководство пользователя и справочник команд

Поделиться
Скачать
Roving Networks RN-171 Скачать руководство пользователя страница 19

WiFly GSX

 

www.rovingnetworks.com

 

 

 

 

 

WiFlyRN171-um      2/23/2011

 

809 University Avenue 

•

 Los Gatos, CA 95032  

•

Tel (408) 395-6539 

•[email protected]

 

~

 

19

 

~

 

If this setting is enabled (set uart mode 0x10), any unsent RX data is still in the buffer is flushed when a 
connection is closed.  
 
 

setuarttx<0, 1>

 

Disables or enables the TX pin= PIO10 of the UART.   Disable will set 
PIO10 to an INPUT with weak pulldown. 

 

NOTE:   Due to an issue in the UART hardware, the UART does not support even or odd parity. 

 

5.11.

 

WLAN Parameters 

 

setwlanauth<value>

 

Sets the authentication mode. Not needed unless using auto join mode 2. 
i.e. 

set wlan join 2 

 

Note: During association the WiFly module interrogates the Access Point 
and automatically selects the authentication mode.  

 

The current release of Wifly firmware supports these security modes: 
• WEP-128 (open mode only, NOT shared mode)  
• WPA2-PSK (AES only)  
• WPA1-PSK (TKIP only)  
• WPA-PSK mixed mode  (some APs, not all are supported)  
 

Value 

Authentication Mode 

0 Open 

(Default) 

1 WEP-128 
2 WPA1 
3 

Mixed WPA1 & WPA2-PSK 

4 WPA2-PSK 
5 Not 

Used 

6 

Adhoc, Join any Adhoc network 

 
 

setwlan channel <value>

 

sets the wlan channel,  1-13 is the valid range for a fixed channel.   If 0 is 
set, then scan is performed, using the ssid, for all the channels set in the 
channel mask. 

 

setwlanext_antenna<0, 1>

 

determines which antenna is active, use 0 for chip antenna, 1 for UF.L 
connector. Default = 0.  Only one antenna is active at a time and the 
module must be power cycled after switching the antenna. 

 

setwlan join  <value>

 

sets the policy for automatically joining/associating with network access 
points.  This policy is used when the module powers up, including wake 
up from the sleep timer. 

 

Содержание RN-171








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды