rotork YT-3100 Скачать руководство пользователя страница 8

Страница: 8 / 68

Smart Positioner

YT-3100

Product Manual

Ver. 1.19

2.3

Label Description

•

MODEL :

Indicates the model number and any options of the positioner.

•

EXPLOSION PROOF :

Indicates certified explosion proof grade.

•

INGRESS PROTECTION : Indicates enclosure protection grade.

•

INPUT SIGNAL :

Indicates input signal range.

•

OPERATING TEMP. :

Indicates the allowable operating temperature.

•

SUPPLY PRESSURE :

Indicates the supply pressure range.

•

SERIAL NUMBER :

Indicates unique serial number.

•

MONTH.YEAR :

Indicates manufactured month and year.

•

INTRINSIC SAFETY / NONINCENDIVE : Indicates intrinsic safety explosion proof grade.

•

AMBIENT TEMP. :

Indicates the allowable ambient temperature for explosion proof.

•

Ui, Ii, Pi, Ci, Li :

Indicates the allowable electrical data in the certificate.
You can also see the details in the certificate.

※

Precautions

Be careful not to apply volatile solvent (hardener of instant adhesive, acetone, WD-40, etc.) to the

sticker nameplate. Printed contents may be erased.

Fig. L-1: Non-explosion proof

Fig. L-2: Intrinsic safety type (ATEX, IECEx, NEPSI, KCs)

Содержание YT-3100





































































Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды

rotork YT-3100, Руководство по эксплуатации продукта

Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды