rotork YT-3100 Скачать руководство пользователя страница 47

Страница: 47 / 68

Smart Positioner

YT-3100

Product Manual

Ver. 1.19

9.9.6

User Set Characterization 5 Points (U5)

A total of 5 target positions are set every 4 mA intervals. When shipped from the factory, the initial

positions are P0 (4 mA, 0 %), P1 (8 mA, 25 %), P2 (12 mA, 50 %), P3 (16 mA, 75 %), and P4 (20 mA,

100 %). User can change all 5 points or only change partially and exit the menu by pressing <ESC>

button.

3 seconds

→

Press <UP> or

<DOWN> button

if the above is not

displayed.

Press <UP> or

<DOWN> button

if the above is not

displayed.

→

→

→

→

→

To automatically

move after

several seconds.

→

<ESC>
2 times

→

This function is activated by saving the Valve Flow Characterization Curves (CHAR) of above Section

9.9.5 as “U5”.

Содержание YT-3100





































































Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды

rotork YT-3100, Руководство по эксплуатации продукта

Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды