rotork YT-3100 Скачать руководство пользователя страница 15

Страница: 15 / 68

Smart Positioner

YT-3100

Product Manual

Ver. 1.19

Installation

3.1

Safety

When installing a positioner, please ensure to read and follow safety instructions.

➢

Any input or supply pressures to valve, actuator, and / or to other related devices must be turned

off.

➢

Use bypass valve or other supportive equipment to avoid entire system “shut down”.

➢

Ensure there is no remaining pressure in the actuator.

➢

The positioner has a vent cover to exhaust internal air and drain internal condensation water.

When installing the positioner, make sure the vent cover must be facing downward. Otherwise,

the condensation water could cause damages to PCB.

Fig. 3-1: The correct positions of a vent cover

3.2

Tools for installation

➢

Hex key set for hex socket cap bolts

➢

(+) & (-) Screw drivers

➢

Spanners for hexagonal-head bolts

Содержание YT-3100





































































Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды

rotork YT-3100, Руководство по эксплуатации продукта

Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды